|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
 ;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
;
Complete manual including mechanical part in good pdf quality. Shaded greys of the pcb due to pdf not perfect but usable.
To erase a character
5
Press YES.
Press m/M repeatedly until the character to be erased flashes, then press CLEAR.
9
Press YES.
The whole name appears in the display, followed by �Complete!!� to indicate that the labeling procedure is completed.
To cancel the operation
The whole name appears in the display, followed by �Complete!!� to indicate that the labeling procedure is completed.
To cancel the operation
Press MENU/NO or x. Copying a track or disc name You can copy an existing track or disc name and use it to name another track on the same disc or the disc itself.
Press MENU/NO or x. Naming a track or an MD using the remote Z
1
1
Press NAME EDIT/SELECT while the deck is in one of the operating modes listed below, depending on what you want to name: To name A track The MD Press while the deck is Playing, paused, recording, or stopped with the track number displayed Stopped with total number of tracks displayed
While the deck is stopped, playing, or paused, press MENU/NO.
�Edit Menu� appears in the display.
2 3 4
Turn AMS (or press ./> repeatedly) until �Name ?� appears, then press AMS or YES. Turn AMS (or press ./> repeatedly) until �Nm Copy ?� appears, then press AMS or YES. Turn AMS (or press ./> repeatedly) until the track number (when copying the track name) or �Disc� (when copying the disc name) flashes, then press AMS or YES to copy the selected name. When �No Name� appears in the display
Editing Recorded MDs
A flashing cursor appears in the display.
2
Press NAME EDIT/SELECT repeatedly to select the character type. To select Press repeatedly until Uppercase letters �Selected AB(C)� appears in the and symbols1) display Lowercase letters �Selected ab(c)� appears in the display and symbols1) Numbers �Selected 12(3)� appears in the display 1) Only � � / , . ( ) : ! ? can be selected.
The selected track or disc has no name.
5
Turn AMS (or press ./> repeatedly) until the track number (when naming a track) or �Disc� (when naming a disc) flashes, then press AMS or YES to enter the copied name.
�Complete!!� appears for a few seconds and the name is copied.
To cancel the operation
3
Enter a character using letter/number buttons. If you have selected uppercase or lowercase letters
Press MENU/NO or x.
1 Press the corresponding letter/number button repeatedly until the character to be entered flashes. Or, press the button once and press ./> repeatedly. To select symbols, press . repeatedly while �A� is flashing. 2 Press M. The flashing character is entered and lights continuously and the cursor shifts to the right.
If you have selected numbers
z When �Overwrite ?(?)� appears in step 5 above
The track or the disc selected in step 5 already has a name. If you wish to replace the name, press AMS or YES again while the indication appears in the display.
Renaming a track or MD Z
1
Press NAME EDIT/SELECT while the deck is in one of the operating modes listed below, depending on what you want to rename: To rename A track The MD Press while the deck is Playing, paused, recording, or stopped with the track number displayed Stopped with total number of tracks displayed
Press the corresponding number button. The number is entered and the cursor shifts to the right.
4
Repeat steps 2 and 3 to enter the rest of the name. To change a character
Press m/M repeatedly until the character to be changed flashes, press CLEAR to erase the character, then repeat steps 2 and 3.
A track or disc name appears in the display.
2
Press down CLEAR until the selected name is erased completely.
36
Naming a track or MD
|
|
|
> |
|
