PHILIPS MG3.2E AA
Service Manual

EN 8 3.

Select the INSTALLATION menu
Surround loudspeakers i 0 0 active A.The other loudspeaker B is a passive U f h é Press U and f at the same time.
INSTANT

�

y� ZOOM

& Open door of the remote control. There are two surround loudspeakers supplied. One is the

X ® q P

one which has to be connected with the active

loudspeaker.

A � The slide channel switch 1 at bottom of the active
loudspeaker has been set default to channel 1 in the factory. See also Sound Setup, p. 9.

MG3.2E

� Connect active to passive loudspeaker with the
supplied speaker cable 2. 1 Insert marked wire into openings of the same coloured connector clips on both speakers. Do not insert To use the menus the wires too far.

& Use cursor in the up/down, left/right directions to select a menu item.
TV VCR DVD SAT

w

� The Surround sound loudspeakers can be located behind

or to either side listener.The front of the B é Press the OK key to activate. loudspeakers do not have to face the listener. The distance between TV and the surround speakers Use � key return or to switch the menu off. �
TUNER CD TAPE CDR

S Q
MOVIE SPORT CHILD NEWS PIXEL PLUS

B A should not exceed 15 m.
Note: In rare occasions people moving around close to the TV
æ b MENU TITLE

may interfere with the sound transmission.

� Set position switch 3 to right if the active o
Subject 1
�
OK MENU

loudspeaker is positioned to right side of the listener, return or switch Subject 2 if it is positioned to left side of the listener main menu off Subject 3

p �
J Subject 4 L M (seen from point view of watching the TV).
V ¬ P

�
activate mains cable 4.

� Connect active loudspeaker to mains with the Subject 6 � Switch on active loudspeaker with the
1 2 3

Directions for Use

select menu item Subject 5

POWER switch 5.

5 2 3 4
The red indicator at front of the active surround shows that the speaker is in standby. During sound transmission the indicator turns to green. Store TV channels 10-15 min. after sound transmission of has After new or extra channels have been stored, the TV automatically transfers those stopped, indicator turns back red indicate TV channels to video recorder if it is equipped with the EasyLink function. The low power standby. message EasyLink : Downloading ...... appears on the screen. The programme list of To switch active speaker off, use switch. recorder now same as one of TV. If the TV is connected to a video POWER recorder which supports NEXTVIEWLink function, TV also automatically transfers the language and country selections to the video recorder.

Keys on top of the TV Select the menu language and country
First, select your language and country.
J MENU INSTALLATION TITLE Menu language

& Select Menu language and press the OK key. é Select your language and press the OK key. Press the M key repeatedly to select Volume, Brightness,
Use cursor up/down scroll through the list and to bring up other Colour, Contrast, Treble and Bass.

Press P or + keys to carry out the selected adjustment. languages which are not displayed on the screen at present. When menu adjustment is not displayed, the Por + Select and press the OK key. � Country keys enable you to select TV channels, the V or +
J MENU Menu TITLE language English countries which are not displayed on the screen at present.

� Select country where you are now located and press the OK key. keys to adjust the volume.

Use cursor up/down to scroll through the list and bring up other The selected adjustment automatically switches off when no action Select Other when none of the countries applies.
J Country You can now search for and store the TV channels in two different ways: MENU TITLE

V P

M

.... has been executed for 10 seconds.

....

Should your remote control be lost or broken you can still using automatic or manual installation (tuning-in channel by change some of basic picture settings with the keys on channel). UK Select your choice and press the OK key.

.... top of the TV. ....

4 Preparation Installation 5