CASIO MTG700M-9DR
Owner's Manual

USER�S GUIDE 2549
To turn an alarm on and off 1. In the Alarm Mode, use D and B to select an alarm. Alarm on indicator 2. Press A to toggle it on and off. � Turning on a alarm (AL1to AL4, or SNZ) displays the alarm on indicator ( ) on its Alarm Mode screen. � In all modes, the alarm on indicator is shown for any alarm that is currently turned on. � The alarm on indicator and applicable alarm number indicator flash while the alarm is sounding. � The snooze alarm indicator ( ) flashes during the 5-minute intervals between alarms.
Alarm number indicator (Alarm 3)

To measure times with the stopwatch Elapsed Time
Start Split Time Start Two Finishes Start Split
First runner finishes. Display time of first runner.

Stop

Re-start

Stop

Clear

Split
(

displayed)

Split release

Stop

Clear

� In other modes besides the each alarm that is currently indicators are displayed for Alarm Mode, alarm number turned on.

Stop
Second runner finishes.

Split release
Display time of second runner.

Clear

To turn the Hourly Time Signal on and off 1. In the Alarm Mode, use D and B to select the Hourly Time Signal (SIG). 2. Press A to toggle it on (ON) and off (OFF). � The Hourly Time Signal on indicator ( ) is shown on the display in all modes while this function is turned on.

� The time on the screen may not appear to stop immediately when you press a button to stop timing or to perform a split operation. Despite this, the time recorded by your button operation is accurate.

Backlight
Hourly time signal on indicator

The backlight uses an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. The watch�s auto light switch automatically turns on the backlight when you angle the watch towards your face. � The auto light switch must be turned on (indicated by the auto light switch on indicator) for it to operate. � See �Backlight Precautions� for other important information about using the backlight.
Auto light switch on indicator

Countdown Timer
Timekeeping Mode time

Hours

Minutes

You can set the countdown timer within a range of one minute to 24 hours. An alarm sounds when the countdown reaches zero. � You can also select auto-repeat, which automatically restarts the countdown from the original value you set whenever zero is reached. � The initial default countdown start time when you purchase the watch or after you have its battery replaced is 15 minutes. � Countdown timer functions are available in the Countdown Timer Mode, which you can enter using C.

To turn on the backlight manually In any mode, press L to illuminate the display for about one second. � The above operation turns on the backlight regardless of the current auto light switch setting.

About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for about one second, whenever you position your wrist as described below in any mode. Moving the watch to a position that is parallel to the ground and then tilting it towards you more than 40 degrees causes the backlight to turn on.
Parallel to ground More than 40 °

Seconds

To use the countdown timer Press D while in the Countdown Timer Mode to start the countdown timer. � When the end of the countdown is reached and auto-repeat is turned off, the alarm sounds for 10 seconds or until you stop it by pressing any button. The countdown time is automatically reset to its starting value after the alarm stops. � When the end of the countdown is reached and auto-repeat is turned on, the alarm sounds, but the countdown starts again automatically whenever the countdown reaches zero. � The countdown timer measurement operation continues even if you exit the Countdown Timer Mode. � Press D while a countdown operation is in progress to pause it. Press D again to resume the countdown. � To completely stop a countdown operation, first pause it (by pressing D), and then press B. This returns the countdown time to its starting value. To set up the countdown timer 1. While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the hour setting of the countdown start time starts to flash, which indicates the setting screen. � If the countdown start time is not displayed, use the procedure �To use the countdown timer� to display it. 2. Press C to move the flashing in the sequence shown below to select other settings.
Hours Minutes Auto-repeat

Warning! � Always make sure you are in a safe place whenever you are reading the display of the watch using the auto light switch. Be especially careful when running or engaged in any other activity that can result in accident or injury. Also take care that sudden illumination by the auto light switch does not surprise or distract others around you. � When you are wearing the watch, make sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off In the Timekeeping Mode, hold down L for about one second to toggle the auto light switch on ( displayed) and off ( not displayed). � The auto light switch on indicator ( ) is on the display in all modes while the auto light switch is turned on. � In order to protect against running down the battery, the auto light switch automatically turns off approximately six hours after you turn it on. Repeat the above procedure to turn the auto light switch back on if you want.

3. While a setting is flashing, use D and B to change it as described below.
Screen 0:15 RPTOFF To do this: Change the hours or minutes Toggle auto-repeat on (ON) and off (OFF) Do this: Use D (+) and B (�). Press D.

Reference
This section contains more detailed and technical information about watch operation. It also contains important precautions and notes about the various features and functions of this watch.

� To specify a countdown start time of 24 hours, set 0:00. 4. Press A to exit the setting screen. � The auto-repeat on indicator ( ) appears on the display while this function is turned on. � Frequent use of auto-repeat and the alarm can run down battery power.

Inputting Text
The following describes how to input text in the e-DATA MEMORY and Alarm Modes.

To input characters
Cursor

Stopwatch
Seconds Hours

1. When the cursor is on the display, use D and B to cycle through the available letters, numbers and symbols, in the sequence shown below.

The stopwatch lets you measure elapsed time, split times, and two finishes. � The display range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds. � The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. � The stopwatch measurement operation continues even if you exit the Stopwatch Mode. � Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement. � All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.

Press (space) to (symbol)

. to (lower-case)

Press

. to (upper-case) to (number)

1/100 second Minutes

2. When the character you want is at the cursor position, press C to move the cursor to the right. 3. Repeat steps 1 and 2 to input the rest of the characters you want. � See the �Character List� for information about the characters you can input.

3