|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I'm happy. Good quality. Very helped me with my work..............................
;
This is the second Manual I have ordered from owner-manuals, I give it five stars because it is exactly what I expected given the age of the equipment. So the contents look a bit aged and the pictures a bit grainy, it fulfills my needs and I am glad I can still get hold of them.
;
thank u so much for this manual that was so cheap that i thought it was a scam but i gambled anyway because it was too good of a deal to pass up and behold,the manual has everything and details of everything even the screws and im still amazed and very happy with my manual .so take my word and jump on it before they realize how cheap they selling thier manuals..thank you so much for taking time to read my thoughts
 ;
I do not have very much to say.
The price is quite covenient, delivery was better as promised (about 12 ours, against the specified 24 hours if I remember well), and the quality of the PDF is more than acceptable.
The Service Manual of Sansui R30 itself is also satisfactory: good graphic for schematics and layouts, simple and well structured.
Giovanni Bianchi
;
Happy to find finally a schematic for this amplifier. The schematic is of good quality, the pcb layout is useless: all is black. Never the less, it is very easy to find the components on the board using the schematics.
3-1
3-1
DISASSEMBLY INSTRUCTIONS
Dismantling of the Front Panel Assembly
1) Open the DVD Tray by using the Open/Close Button while the Set is ON and disconnect the mains supply after removing the Tray Cover. 2) Return the set to its upright position and remove the Tray Cover as shown in Figure 3 and close the tray manually by pushing it back in. 3) Loosen 9 screws and remove the Top Cover by lifting the rear portion upwards before sliding it out towards the rear. - 5 screws on the back - 2 screws each on the left & right side 4) Loosen 7 screws & lift up the top edge of Front Panel assembly to free some catches before sliding it out towards the front. - 4 screws on the bottom - 1 screw "C" on the inside as indicated in Figure 5. - 1 screw each on the left & right side
2mm
Dismantling of the Main Board 1) Loosen 5 screws "B" on the top of main board as shown in figure5.
2) Loosen 9 screws "D" at the back panel as shown in figure 6. 3) Remove all connectors on the RGBScart and main board.
Note: If this is not possible, the DVD Tray has to be open manually.
Take a mini screw driver about 2mm diameter and make a marking 24mm from the tip as shown in figure 2. place the set on its side, insert the mini screw driver till the marking and slide it towards the right as shown in figure 1 until the Tray moves out of the Front Panel.
B
RGB Jack use for MX3600/37 ; MX3700/37S Scart Jack use for MX3800/22S only
C
Repeat
Figure 5
D
Figure 1
Marking just outside the slot on the rear cabinet.
Figure 6
Dismantling of the Servo Board
1) Loosen 4 screws "A" to remove the Servo Board from the DVD Module as shown in figure 4
Dismantling of the Tuner Board 1) Loosen 4 screws "E" on the bottom cover as shown in figure 7.
3) Loosen 4 screws "F" at the top of the Power Board as shown in figure 8
24mm
Figure 2
A
F
E
Figure 3
Note: Do not lost the limited parts of the Servo board
Figure 4
Figure 7
Figure 8
|
|
|
> |
|
