|
|
|
Who's Online
There currently are 5918 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Manual was delivered in a timely manner and was all in English as advertised. The manuals I received when we moved into our flat were in German, Italian, and French. Having never used a steamer before, and not speaking/reading German very well, I needed an English Manual. this was a huge help.
 ;
Great Manual. This manual is available no where else. It was exactly what I was looking for. Only in German.
;
This GRUNDIG UV5A Owner Manual is not only an instruction manual but a total functional circuit description of the Multimeter and includes circuit diagram at the end pages. It is very helpful for repairing and calibrating the instrument. It is written in two languages English and German for international support. It was very easy to repair my unit with this document. Regards, Regis Pauly, Electrical Engineer.
;
The owner's manual was evetything I thought it would be. I was able to print it out using both sides of the paper in quick order, saving me a search online for a used one.
;
Хорошее качество сканирования.
Мануал пришел часов эдак через 12. В целом доволен.
TUNER
Tuning to radio stations
You can search for radio stations by scanning the frequency band. You can also key in the frequency of a known radio station. If an FM station is being broadcast and received in stereo, STEREO is shown. Searching for radio stations 1 Turn SOURCE SELECTOR to select the tuner. yTUNER is displayed. 2 Select a waveband by pressing TUNER BAND repeatedly. yThe selected waveband is displayed. 3 Keep 1 or 2 pressed for approximately 1 second. ySEARCH is displayed and the tuner tunes to a station with sufficient strength. 4 Repeat this procedure until you find the desired station. � To fine tune to a weak transmitter, briefly press 1 or 2 as often as necessary for optimum reception. Tuning to a radio station by frequency (with the remote control only) 1 Press TUNER. yTUNER is displayed. 2 Press FR. D.. y_ is displayed. 3 Use 1�0 to key in the frequency of a radio station. Notes: Only valid numbers within the frequency range of the tuner can be keyed in.
Storing radio stations
You may store up to 30 radio stations in the memory. The receiver can select and program radio stations by itself or you can choose them yourself. Automatic programming 1 Choose * TUNER from the menu and press NEXT 2. 2 Choose AUTO INSTALL and press NEXT 2. yThe preset number where programming will start, the waveband and AUTO are displayed. 3 Turn TUNER PRESET X to change the preset number where programming should start. 4 Use TUNER BAND to switch to the desired waveband. 5 Press ENTER / OK to start programming. yAUTO INSTALL flashes and all available radio stations are programmed, this may take a few minutes. Programming is done when AUTO INSTALL stops flashing. Manual programming 1 Choose * TUNER from the menu and press NEXT 2. 2 Choose MAN INSTALL and press NEXT 2. yA preset number, the waveband and the frequency are displayed. 3 Turn TUNER PRESET X to change to the preset number where the radio station should be stored. 4 Tune to the desired radio station (see �Searching for radio stations�). 5 Press ENTER / OK to confirm your selection. ySTORED is displayed briefly. The radio station is programmed at the chosen preset number. 6 Select and store all desired radio stations this way.
Switching FM sensitivity
You can switch the tuner to a lower search sensitivity, to search only for stations with a strong signal (FM only). 1 Turn SOURCE SELECTOR to select the tuner. yTUNER is displayed. 2 Press SENS. on the receiver. yEither SENS HI or SENS LO is displayed for 5 seconds. Note: While searching for radio stations, the actual sensitivity is displayed. In this case, SENS LO means the tuner is looking only for radio stations with a strong signal.
23
English
|
|
|
> |
|
