|
|
|
Who's Online
There currently are 5858 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
;
Nothing wrong with the manual or the delivery - came to me the same day I ordered it. But afterwards I realized that I ordered the wrong manual. Probably better with the Quick start - version. So maybe it would be better if we could see a list with inhold for each manual before ordering?
 ;
Bought T4850 High End Tuner a few years ago, but i didn't know where all the buttons were used for. So i purchased the owners manual. Perfect! Just what i needed.
4 2
Getting the best results
J
The nozzle is designed to vacuum hard floors, rugs and carpets. To avoid blockages and maintain suction efficiency, the floor nozzle should be cleaned regularly using the hose handle.
Dust bag safety device To avoid damaging the cleaner, do not use it without a dust bag. A safety device is fitted which prevents the cover closing without a dust bag. Do not attempt to force cover shut. Changing/Cleaning the filters There are two filters inside your cleaner. Never use the cleaner without the filters in place. To clean Motor Protection filter: The Motor Protection filter should be cleaned when dirty. D Release catch, remove lid and filter. E Wash filter in warm water. F Allow to dry and re-insert clean filter. Close lid. To change Micro filter: The Micro filter should be changed every fifth dust bag. G Release catch, open the filter cover and remove filter. H Insert new filter and close cover.
p r
Loose rugs/curtains/lightweight fabrics: Reduce the suction power. Use the floor nozzle for loose rugs and the upholstery nozzle for curtains, cushions etc. Confined areas: Use the crevice nozzle for crevices, corners and radiators. Dust bag indicator and changing the dust bag For peak performance the dust bag must be changed when full. Check the dust bag regularly and replace when necessary. The dust bag indicator window will gradually turn red when filling and completely red when full. If the dust bag should accidentally get broken in the cleaner, take cleaner to Progress Service Centre for cleaning. To check the dust bag, the cleaner must be switched on, with all attachments connected and off the floor. The dust bag full indicator may signify that the bag is blocked (occasionally caused by very fine dust) which will cause loss of suction and may result in overheating. If this occurs change the dust bag even if it is not full. To change the dust bag: A Release catch and remove lid. Before removing the dust bag, bend the tab into the hole to prevent dust escaping. B Remove the dust bag. C Insert new dust bag by sliding the bag slots into the holder. Close lid. We recommend the dust bag is changed: * after using a carpet cleaning powder. * if there is a bad smell from the cleaner, then you should also change the filter. Note: use only Progress original dust bags and filters: 5 Dust bags and 1 Micro filter (Ref T196)
Troubleshooting
1. Power: If the electric power does not come on, disconnect from mains and check plugs, cable and fuses where appropriate. 2. Blockages/dirty filters: The cleaner may switch itself off in the event of a severe blockage or excessively dirty filter(s). In such cases, disconnect from mains and allow to cool for 20-30 minutes. Clear blockage and/or replace filter(s) and restart. The clearing of blocked hoses is not covered by the guarantee. 3. Water: If water is sucked into the cleaner the motor must be changed at a Progress Service Centre. See additional Progress information towards the back of this booklet.For
healthier
homes
|
|
|
> |
|
