|
|
|
Who's Online
There currently are 5765 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
;
Copy of genuine owners/operators manual, very useful
;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
12. Removal of CCD C.B.A., Filter Rubber, Optical Filter, Optical Filter Stopper, IR Cut Filter CAUTION: 1) When removing the CCD C.B.A., take care that the Optical Filter and the IR Cut Filter do not fall out. 2) Take extreme caution when removing the CCD C.B.A. because it is easily damaged by static electricity. Use a Wrist Strap while removing and installing. 3) Do not touch the CCD window surface. Installation of CCD C.B.A., Filter Rubber, Optical Filter, Optical Filter Stopper, IR Cut Filter 1) Install the IR Cut Filter in the Lens Unit correctly. Note: Make sure no dust gets on the IR Cut Filter or in the Lens Unit. Clean the IR Cut Filter with lens cleaning paper dampened with lens cleaner if necessary. 2) Install the Optical Filter Stopper on the IR Cut Filter correctly. Note: Make sure that no dust gets on the Optical Filter Stopper. 3) Install the Optical Filter on the IR Cut Filter correctly. Note: Make sure no dust gets on the Optical Filter or in the Lens Unit. Clean the Optical Filter with lens cleaning paper dampened with lens cleaner if necessary. 4) Install the Filter Rubber on the Optical Filter correctly. Note: Make sure that no dust gets on the Filter Rubber.
chamfering chamfering
15. Installation of Battery Catcher Unit 1) To remove the Battery Catcher Unit, first remove the Backup Cover (29) with the Battery. 2) Remove a Screw (586). 3) Slide the Battery Catcher Unit out by pushing Portions A and B as indicated by the arrow.
WARNING: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. Portion A
586
Slide Battery Catcher Unit
Push Push
Fig. D9 16. Replacement of Lamp When replacing the Lamp, refer to "HOW TO REPLACE THE LAMP" in "SERVICE NOTES."
Portion B
DANGER:
Use only replacement Lamp (PART NO. VLLW0015) supplied by Panasonic to reduce risk of fire. Handle new Lamp with cloth or tissue as skin oils will decrease Lamp life. Remove Light Protector and allow Lamp to cool before replacing to avoid possible burn hazard.
chamfering Filter Rubber (VM-D52/PV-L352-K)
chamfering Filter Rubber (PV-L552-K)
5) Install the CCD C.B.A. in the Lens Unit. Then, secure the 2 Screws (502) while keeping the CCD C.B.A. pressed toward the upper right corner. Note: Do not touch the Lens Surface. Clean the surface with lens cleaning paper dampened with lens cleaner if necessary. 13. Installation of Zoom Motor Unit Install the Zoom Motor Unit so that the Shaft of the Zoom Motor Unit is set in the Holder. Then, tighten the 2 Screws (501). 14. Installation of Top Operation Unit 1) Install the Top Operation Unit to the Side Case R Unit while setting the Locking Tab (L-2). 2) Then, secure the 2 Locking Tabs (L-1).
|
|
|
> |
|
