|
Who's Online
There currently are 5944 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I work at an authorized service center and I can tell if a manual is as it should be. This one is. It may be a scan, but a very good one at that. The interesting part for me was the curcuit diagram which was scanned at high quality, making it as good as the original. I will definitely be back as a customer. I need not say this, but I will: the price was the best. Thank you owner-manuals.com .
;
really a very good manual even sometimes the quality is no so good as before still very readible and very very useful!
;
FAST very good and clear a great unexpensive job!!! very recomended for all people who are preofessional or hobbists as me!!!!!!
;
Thank you very much for this Service Manual, it helped us a lot to repair the M-4318!
...BUT: The parts list is missing and the free parts katalog on web isn't complete, so now we don't know the part numbers of the defect parts :(
We had to build them out of a working machine, and need the numbers to reorder the missing parts now.
;
Very good manual with clear electrical diagrams. Thanks owner-manuals.
3-4. FOCUS ADJUSTMENT
1. Receive the monoscope signal. 2. Set the CONTR control to normal. 3. Adjust the FOCUS control of the FBT so that the focus at the center of CRT screen and around the CRT screen become optimum.
3-5-2. White Balance Adjustment
1. Receive the color bars signal. (Set the BURST switch of the test signal generator to OFF.) 2. Set the following controls on the front panel as follows: BRIGHT 8 Center click CONTR 8 Minimum BIAS (Front panel) 8 50 % GAIN (Front panel) 8 50 % 3. Adjust RV118 (SUB BRT) on the B board so that the blue stripe portion on the color bars signal is bright dimly.
Colorbar pattarn
FOCUS
FBT
Fig. 3-14
3-5. WHITE BALANCE ADJUSTMENT
3-5-1. Screen Voltage Adjustment
1. Receive the dot signal. 2. Connect a digital voltmeter to pin 5 (KG) of CRT socket. Adjust RV119 (G C/O) on the B board so that the voltage is 103 Vdc. 3. Connect a digital voltmeter to pin 9 (KB) of CRT socket. Adjust RV121 (B C/O) on the B board so that the voltage is 103 Vdc. 4. Adjust the SCREEN control of the FBT to the position where just before the flyback line disappears from the CRT screen.
WHITE Fig. 3-16
FBT
4. Receive the white signal. (Set the BURST switch of the test signal generator to OFF.) 5. Set the CONTR control to 90 degrees clockwise from the center position. 6. Using the luminance meter, adjust the luminance level of the CRT screen so that it is 3 Nit. (Screen is bright dimly.) 7. Adjust the white balance of the cut-off with RV119 (G C/O) and RV121 (B C/O) on the B board. 8. Set the luminance level of white signal to 100 IRE with test signal generator. 9. Adjust the white balance of the high-light with RV120 (G GAIN) and RV122 (B GAIN) on the B board. 10. Press the BLUE ONLY switch on the front panel. 11. Adjust the white balance of the high-light with RV124 (R GAIN/BL) and RV125 (G GAIN/BL) on the B board. 12. Using the luminance meter, adjust the luminance level on the CRT screen with test signal generator so that it is 8 Nit. Then confirm that the white balance is adjusted correctly.
YELLOW CYAN GREEN MAGENTA RED BLUE BLACK
SCREEN
Fig. 3-15
S MIC Chassis
3-5
|
|
|
> |
|