|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good product and very helpfull to repair. Many thanks.
;
Very good product. Best service manual. Many thanks
;
I am only search for 5 Minute, by it in 5 Minutes to and get ist in few ours! Best i found in the Internet and my Amplifer is repaired as well! Thank you
 ;
Readable text and good copy. Very much needed if you wish to do some repairs on this fine old unit.
;
Fint forløb med levering af manualen. Kvaliteten af skanningen betegnes som middel
COMPONENT REPLACEMENT AND ADJUSTMENT
MAGNETRON REMOVAL
1. CARRY OUT 3D CHECKS. 2. Remove the two (2) screw holding the chassis support to the oven cavity and the magnetron. 3. Disconnect the H.V. wire B and filament lead of the transformer from the magnetron. 4. Release the chassis support from the oven cavity. 5. Move the air intake duct to left. 6. Remove the air deflector A from the magnetron. 7. Carefully remove two (2) screws holding magnetron to waveguide, when removing the screws hold the magnetron to prevent it from falling. 8. Remove the magnetron from the waveguide with care so the magnetron antenna is not hit by any metal object around the antenna. 9. Remove the magnetron cushion from the magnetron. CAUTION: WHEN REPLACING THE MAGNETRON, BE SURE THE R.F. GASKET IS IN PLACE AND THE MAGNETRON MOUNTING SCREWS ARE TIGHTENED SECURELY.
FAN MOTOR REPLACEMENT REMOVAL
1. CARRY OUT 3D CHECKS. 2. Remove the one (1) screw holding the noise filter to the chassis support. 3. Release the noise filter from the tabs of the fan duct. 4. Disconnect the wire leads from the fan motor. 5. Remove the one (1) screw holding the fan duct to the oven cavity back plate. 6. Remove the fan duct from the oven. 7. Remove the fan blade from the fan motor shaft according to the following procedure. 1) Hold the edge of the rotor of the fan motor by using a pair of groove joint pliers. CAUTION: � Make sure that any pieces do not enter the gap between the rotor and the starter of the fan motor. Because the rotor is easy to be shaven by pliers and metal pieces may be produced. � Do not let the pliers touch the coil of the fan motor because the coil may be cut or damaged. � Do not distort the bracket by touching with the pliers. 2) Remove the fan blade from the shaft of the fan motor by pulling and rotating the fan blade with your hand. 3) Now, the fan blade will be free. CAUTION: � Do not use this removed fan blade again. Because the hole (for shaft) of it may become bigger than a standard one. 8. Now, the fan motor is free.
Shaft
Coil Groove joint pliers
INSTALLATION
1. Install the fan blade to the fan motor shaft according the following procedure. 1) Hold the centre of the bracket which supports the shaft of the fan motor on the flat table. 2) Apply the screw lock tight into the hole (for shaft) of the fan blade. 3) Install the fan blade to the shaft of fan motor by pushing the fan blade with a small, light weight, ball peen hammer or rubber mallet.
CAUTION: � Do not hit the fan blade when installed because the bracket may be deformed. � Make sure that the fan blade rotates smoothly after installation. � Make sure that the axis of the shaft is not slanted. 2. Install the fan duct to the oven cavity back plate with the one (1) screw. 3. Install the noise filter to the fan duct and the chassis support with the one (1) screw. 4. Re-connect the wire leads to the fan motor.
Shaft
Stator Gap Bracket Rotor
Axis Stator Rotor
These are the position where should be pinched with pliers
Table
Center of bracket
Rear view
Side view Figure C-1 Fan motor replacement
R-632 24
|
|
|
> |
|
