|
|
|
Who's Online
There currently are 5851 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
;
Manual was complete and available promptly, since I had lost my original manual. Very good response.
;
Whilst this is a photo copy, and some of the pages are a little askew, it was all readable and intact. A real bonus finding an old manual for a classic piece of kit that no other site had.
Great stuff.
;
excellent quality, contains circuits and scan quality, 110 pages
;
It was easy done, and I got exactly what I was looking for.
Adjusting the Volume
You can adjust the volume level between MIN (0) and MAX (32) when the Unit is turned on. Turn the VOLUME control on the Unit to the right or left to increase or decrease the volume level. OR Press the VOLUME + or � button on the Remote Control to increase or decrease the volume level.
Showing the Time (CLOCK/ DISPLAY)
While listening to a CD or the radio, you can see the current time. To display the clock, press the CLOCK/DISPLAY button on the Unit. To return to the original display, press the same button until the original display appears. Note: You need to set the clock first in order for it to work. (See "Setting the Clock" on page 9.)
Adjusting the Brightness (DIMMER) [RD-T7GN Only]
CAUTION: DO NOT turn on the Unit and/or start playing any source without first setting the VOLUME control to MIN (0) , as a sudden blast of sound can damage your hearing. For private listening Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones.
When operated on AC power ����
You can adjust the brightness of the display's backlighting. When the Unit is turned on: Each time you press the SNOOZE/DIMMER button on the Unit or on the Remote Control, the backlight fully turns on or dims. When the Unit is turned off(Standby): Each time you press the SNOOZE/DIMMER button on the Unit or on the Remote Control, the backlight dims or turns off. When the Sleep Timer is on: You can also dims or turn off the backlight with these buttons.
Reinforcing the Bass Sound (AHB PRO) [RD-T7GN Only]
You can reinforce the bass sound to maintain rich, full bass at low volume (you can use this effect only for playback): To get the effect, press the AHB (Active Hyper Bass) PRO button. The �BASS� indicator lights up on the display. To cancel the effect, press the button again. The �BASS� indicator goes out.
When operated on batteries ����
When the Unit is turned on, you can turn on the backlighting of the display for a few seconds. Each time you press the SNOOZE/DIMMER button on the Unit or on the Remote Control, the backlight turns on for a few seconds.
Using Batteries
Power Batteries (6 pcs.): You can operate the System on batteries. When the batteries are exhausted, �NO BATT� will appear on the display. In this case, replace with the new batteries. Memory Backup Batteries (3 pcs.): Your settings such as the preset stations, clock and timer are backed up with this batteries. CAUTION: If memory backup batteries are exhausted or not installed, and the AC power cord is disconnected or there is a power failure, the settings you have made will be erased from memory in approx. half a day.
Tone Control (BASS/TREBLE)
You can control the tone by changing the bass and treble.
I Press the BASS/TREBLE button until "BASS" 1.
or "TREBLE" appears on the display.
Each time you press the button, the display changes as follows: BASS = TREBLE = original display = (back to the beginning)
I Turn the Jog dial on the Unit or press the 2.
VOLUME +/� button on the Remote Control to adjust the level.
The bass or treble level changes between �6 and +6. (0: Flat)
To exit the tone control mode, press the BASS/TREBLE button until the original display appears, or wait for 15 seconds. To forcibly reset the bass and treble levels to 0 (FLAT), press the BASS/TREBLE button for 2 seconds or more.
4
English
|
|
|
> |
|
