|
|
|
Who's Online
There currently are 5983 guests and
2 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Getting Started
This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.
Before Installation
General Precautions
� Be sure your hands are dry. � Turn the power off to all components. � Read the manuals supplied with the components you are going to connect.
Notes:
� Supplied batteries are for the initial setup. Replace for continued use. � For RX-6042S: After replacing the batteries, set the manufacturers� codes again (see pages 35 and 36).
CAUTION: Follow these precautions to avoid leaking or cracking cells: � Place batteries in the remote control so they match the polarity: (+) to (+) and (�) to (�). � Use the correct type of batteries. Batteries that look similar may differ in voltage. � Always replace both batteries at the same time. � Do not expose batteries to heat or flame.
Locations
� Install the receiver in a location that is level and protected from moisture and dust. � The temperature around the receiver must be between �5�C and 35�C. � Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.
Handling the receiver
� Do not insert any metal object into the receiver. � Do not disassemble the receiver or remove screws, covers, or cabinet. � Do not expose the receiver to rain or moisture. Do not connect the AC power cord until all other connections have been made.
Connecting the FM and AM Antennas
FM antenna connections
Checking the Supplied Accessories
Check to be sure you have all of the following items, which are supplied with the receiver. The number in the parentheses indicates quantity of the pieces supplied. � � � � Remote Control (1) Batteries (2) AM Loop Antenna (1) FM Antenna (1)
A
AM P LOO
AM EXT
B
AM P LOO
AM EXT
CO
75 L FMAXIA
TENNA AN
CO
75 L FMAXIA
TENNA AN
Extend the supplied FM antenna horizontally.
AM EXT AM LOOP
If anything is missing, contact your dealer immediately.
Putting Batteries in the Remote Control
Before using the remote control, insert the two supplied batteries first.
FM Antenna (supplied)
1
2 R6(SUM-3)/
AA(15F)
3
FM 75
COAXIAL
ANTENNA
Outdoor FM Antenna Cable (not supplied)
Connect the supplied FM antenna as temporary measure to the FM 75 � COAXIAL terminal�A
1 Press and slide the battery cover on the back of the remote control. 2 Insert the batteries.
� Make sure to match the polarity: (+) to (+) and (�) to (�).
3 Replace the cover.
If the remote control cannot transmit signals or operate the receiver correctly, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.
If reception is poor, connect the outdoor FM antenna (not supplied)�B 1 Disconnect the supplied FM antenna. 2 Connect a 75 � coaxial cable with the standard type connector (IEC or DIN45325).
5
|
|
|
> |
|
