PANASONIC SLSX388
Owner's Manual

Using the Wired Remote Control
The remote control can be operated regardless of the HOLD mode of the unit.

SL-SX390

Basic operation
Press once during off or stop mode.
VOL

Preparation:
Release the remote control from the HOLD mode.
EQ HOLD

Press during play. Skipping tracks
(Press [:] twice to skip to the beginning of the previous tracks.) Backward (Beep Beep Beep)

To start play
(Beep)

VOL

HOLD

Press once during play.
VOL

Searching through tracks

Forward (Beep Beep)

To stop play

� Operation confirmation tones » When an operation button is pressed, a confirmation
tone sounds. Refer to the parentheses in the illustration for the different types of confirmation tones.

Press and hold during play.
(Beep...Beep)
VOL

� Turning the operation tones off and on » While stopped or during play » Press and hold [EQ] on the remote control for 5 seconds until the unit's display appears. The tone sounds when the setting is changed.

Press and hold during play or stop mode. To turn off the unit
VOL

To adjust the volume

Decrease (Beep)

VOL

Increase (Beep)

(Beep...Bee...p)

�The volume range is 0�25. (Press and hold to change the volume successively.) �A tone (beep-beep) sounds when you reach the minimum or maximum volume.

EQ

HOLD

EQ

Changing the sound quality
(Beep)

Press during play or stop mode.

The setting switches in the sequence indicated below each time [EQ] is pressed. S-XBS>TRAIN>Cancel (no indicator is shown)

To turn the tone off

To turn the tone on

EQ

HOLD

EQ

^==========b
(Beep)

S-XBS:
Select this setting to boost the low-range response.

TRAIN:
Select this setting to avoid annoying other passengers with noise from your headphones/earphones while riding on the train, or to reduce fatigue when listening for a long period of time.

Note!
The setting returns to S-XBS when you disconnect the power source.

Using the Unit with Optional Accessories
Using the unit with an audio system
Turn off this unit and the other equipment before connection.
SL-SX390

Using the unit with a car audio system
Headphone jack (�)

Items to be purchased
For connection to the car audio system Car stereo cassette adaptor (SH-CDM10A) Connect the car stereo cassette adaptor to [�] on the unit. (When doing this, set this unit�s volume to 10.) Other equipment For securing the unit and connecting the power supply: �Car adaptor (SH-CDC9) �Car mounting kit (SH-CDF20) Note when using the car mounting kit (SH-CDF20) Bracket 1Remove the screw from the bracket at the rear of the car mounting base. 2Replace the screw in the lower hole of the bracket.

1 Connect the remote control to [�] on the unit. 2 Connect the stereo connection cable to the
mote control and the other equipment.

reL VO

EQ ME MORY/RE

CALL

MO

DE

�The unit may malfunction if you connect directly to [�] on the unit. �Do not connect the cable to the PHONO jacks on

3 Turn

the amplifier. the operation tones off (see above) so they are not heard when you press buttons on the remote control. Make further volume adjustments with the other equipment.

HO

LD

(White) L To CD or
O PEN

AUX (Red) R terminals

4 Set the volume to 10.
SL-SX388

1 Connect the stereo connection cable to [�] on the
unit. 2 Set the volume to 10. Make further volume adjustments with the other equipment.

SL-SX390
VOL

Screwdriver Stereo connection cable (not included)

�When you switch off the car, volume and sound quality may return to the original settings and the resume function may work even if you change the disc. �It may not be possible to use the unit with some types of car stereos owing to restrictions imposed by the construction of the car stereo cassette adaptor. For further details, refer to the instructions of the part concerned.

Note!

Note!
�Obtain the optional connecting cable if the other equipment comes with mini-phone jacks.
SL-SX390

�If you connect speakers (active or otherwise) directly to the unit's headphone jack, ensure they have an impedance of 1 k� or less.

5

RQT6190