|
|
|
Who's Online
There currently are 5410 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
excellent quality, contains circuits and scan quality, 110 pages
;
It was easy done, and I got exactly what I was looking for.
;
The manuel was exactly what I needed and I received it promptly. Thanks
;
Thanks to Owner-Manuals.com! This manual was exactly what I needed. As Amana was purchased by Maytag and later by Whirlpool, there was no way to receive it from their websites. I was lucky to find this resource.
 ;
Great to be able to set channels again, on an old but stoll fine working TV
Thank you for purchasing JVC speakers. Before you begin using them, please read the instructions carefully.
English
Connections
Speaker units
1
Speaker cord Front speaker (2) Center speaker (1) Surround speaker (2)
2
Connect the speaker cords to the speaker terminals.
Press Red (+) Insert Release
Precautions for installation and daily use
� Be sure to have the speakers installed on the wall by a qualified personnel to avoid unexpected damage from falling off the wall due to incorrect installation or weakness in the wall structure. � Care must be taken in selecting the location of installation on the wall. Injuries or damages may result if the speakers installed interfere with daily activities. � The speakers are magnetically shielded to avoid color distortions on TVs if they are installed properly. � When placing the speakers near a TV set, turn off the TV�s main power switch or unplug it before installing the speakers. Then wait at least 30 minutes before turning on the TV�s main power switch again. If there are still distortion, move the speakers further away from the TV. � Do not reproduce sounds at so high a volume that they are distorted; otherwise, the speakers may be damaged by internal heat buildup. � When moving the speakers, do not pull the speaker cords; otherwise, the speakers may fall over, causing damage or injury.
Black (�)
SP-XF20C (Rear)
Copper Black striped
SP-XF20F (Rear)
Press Red (+)
Black (�) Insert Black striped
Connecting the speaker system to the amplifier
Before connecting� � Turn off the power to the amplifier before connecting the speaker system; otherwise, the speakers may be damaged. � The impedance of each speaker is 6 �. Before connecting them to your amplifier, check the speaker impedance range of your amplifier. If the impedance of this speaker is out of the speaker impedance range indicated on the amplifier, you cannot connect this system to the amplifier. � The maximum power handling capacity of the speakers are 100 W. Excessive input will result in abnormal noise and possible damage. � Be sure to turn down the volume level to prevent unwanted noise before performing following operations: � Turning on or off other components, � Operating the amplifier, � Tuning FM stations, � Fast-forwarding a tape, � Continuously reproducing high frequency oscillation or high pitch electronic sounds, � Connecting or disconnecting a microphone. � When using a microphone, do not aim it at the speakers or use it near the speakers; otherwise, the howling which occurs may damage the speakers. � Before replacing the cartridge, always turn off the power to the turntable; otherwise, the clicking noise may damage the speakers.
Copper
Release
SP-XF10S (Bottom)
Black striped Through the hole
Copper
3
Connecting the speakers to the amplifier.
Front left Center Subwoofer Amplifier Front right
Specifications
Type (magnetically-shielded type): SP-XF20F/SP-XF20C: SP-XF10S: Speaker units: SP-XF20F/SP-XF20C: SP-XF10S: Power handling capacity/Impedance: Frequency range: SP-XF20F/SP-XF20C: SP-XF10S: Sound pressure level: SP-XF20F/SP-XF20C: SP-XF10S: Dimensions (W � H � D): SP-XF20F: SP-XF20C: SP-XF10S: Mass: SP-XF20F/SP-XF20C: SP-XF10S: Accessories: Speaker cords: 2-way 3-speaker Bass-reflex type 1-way Bass-reflex type 5.5 cm cone (� 2), 3.0 cm dome 8.0 cm cone 100 W/6 � 90 Hz to 40 000 Hz 80 Hz to 20 000 Hz 81 dB/W�m 75 dB/W�m 84 mm � 211 mm � 88 mm 209 mm � 85 mm � 92 mm 111.5 mm � 139 mm � 106.5 mm 0.87 kg each 0.52 kg each 4 m (� 3); 10 m (� 2)
Surround left
Surround right
Connect the speakers to the speaker terminals of the amplifier with the speaker cords by referring to the diagram below. � Make sure to match the polarity (ª and ·) when connecting the speaker cords. � The diagram below is an example of a typical connection.
FRONT LEFT FRONT RIGHT
FRONT
RIGHT LEFT
CENTER
CENTER
RIGHT
SURROUND SURROUND LEFT BACK SPEAKERS
Recommended to use SP-SB100 (optionally purchased).
SURROUND RIGHT SURROUND LEFT
Design and specifications are subject to change without notice.
�3�
|
|
|
> |
|
