|
|
|
Who's Online
There currently are 5647 guests and
18 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Perfect for my use.Could have better pictures,but otherwise perfect ;)
 ;
This is one of four manuals I have downloaded recently.
Purchase was very straight forward and the authorising email arrived in about 4 hours.
The quality of the scan is good. Print is clear and square to the page edges.
;
Exactly as advertized. High quality digital copy of the Nak 610 user manual. Easy download and access. Highly recommended.
;
The manual was exactly what I wanted and I found it nowhere else. Thanks!
;
Having purchased a 1994 Kenwood music system from a Charity shop in 2013 (it was a high end product in its day), I found myself not quite knowing where to plug in what, and how to do this, that and the next thing. I needed a Manual, and after failure with another online 'Manual provider' I found Owner Manuals dot com. Well, I wasn't sure, but it was only $5, and if things didn't work out, I wouldn't have lost much...
But things DID work out. After paying my childrens inheritance money, $4.99, I was sent a Manual for my Kenwood System very quickly. Alas, it was in German, and being Scottish, I could not read it or get my system in order from it...a rapid email to them brought the English Manual in short order, and my retro-system was and IS up and running in it's regulation settings.
I am very grateful to http://www.owner-manuals.com for their quick service and for even having such an obsolete Manual in the first place! If you need a Manual for ANYTHING, try here first. I wouldn't be surprised if I bought a 1928 Marconi radio, and got the user Manual for THAT here too!
Top marks.
John Copeland
Glasgow
Scotland
www.pioneerelectronics.com
OPERATING INSTRUCTIONS
S-STP500
1 2What's in the box
Check that you have all the supplied accessories before you start: � Front speakers x 2
SPEAKER SYSTEM
Making receiver settings
Before connecting the speakers, please read the Operating Instructions supplied with your VSX-416 receiver to make the following settings: � Switch the speaker impedance to the 6 � setting (see Switching the speaker impedance to do this).
� Center speaker x 1
� Set the crossover frequency to 200 Hz (see Crossover network to do this). After connecting the speakers, please complete Using the Quick Setup with the 5.1ch setting (refer to the receiver�s 5 minute guide in the supplied Operating Instructions).
� Surround speakers x 2
Connecting the speakers
� Speaker cords x 1 � Non-skid pads � Brackets for wall mounting x 4 Important � Make sure all equipment is turned off before making any connections. 1 Twist and pull off the protective shields on each speaker wire. To get the best out of your speakers it is important that you connect them properly to your amplifier or receiver. Each speaker connection consists of a positive (+) and a negative (�) terminal. These should be matched between the amplifier and the speaker.
� Screws x 4 � These operating instructions
Before you start
Thank you for buying this Pioneer product. Please read through these operating instructions before installing and using your speaker system. Important In order to prevent damage to the speaker system resulting from input overload, please observe the following precautions: � Do not supply signal to the speaker system in excess of the maximum permissible input. � When connecting or disconnecting cables, make sure that your amplifier is switched off. � Do not use excessive amplifier volume if using a tone control to emphasize high or low frequencies. Caution � Do not connect the supplied speakers to any amplifier other than the one supplied with this system. Connection to any other smplifier may result in malfunction or fire. � Pioneer will not be responsible for any accidents or damage that may result from improper installation. 2 Attach one end of the supplied speaker cord to the rear of the center speaker. Connect the wire with the colored marker to the red (+) terminal; the plain wire to the black (�) terminal. Press down the spring-loaded tab and insert the wire, as shown below. Release the tab to secure the wire.
Red (+) Black (�) Green colored marker
|
|
|
> |
|
