|
|
|
Who's Online
There currently are 5902 guests and
3 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
- GENERAL
- TEST MODE
- DIAGRAMS
- Circuit Boards Location
- Block Diagrams
- Main Section
- Power Section
- Printed Wiring Board - Digital Section
- Schematic Diagram - Digital Section
- Printed Wiring Board - Main Section
- Schematic Diagram - Main (1/3) Section
- Schematic Diagram - Main (2/3) Section
- Schematic Diagram - Main (3/3) Section
- Printed Wiring Board - Display Section
- Schematic Diagram - Display Section
- Printed Wiring Board - Video/Key Section
- Schematic Diagram - Video/Key Section
- Printed Wiring Board - Power Supply Section
- IC Pin Function Description
- IC Block Diagrams
- EXPLODED VIEWS
- Front Panel Section
- Chassis Section
- ELECTRICAL PARTS LIST
There are currently no product reviews.
 ;
El producto satisface las necesidades del servicio t
;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
z About speaker distances
This receiver allows you to input the speaker position in terms of distance. However, it is not possible to set the center speaker farther away than the front speakers. Also, the center speaker can not be set more that 5 feet (1.5 meters) closer than the front speakers. Likewise, the rear speakers cannot be set farther away from the listening position than the front speakers. And they can be no more than 15 feet (4.5 meters) closer. This is because incorrect speaker placement is not conducive to enjoy the surround sound. Please note that, setting the speaker distance closer than the actual location of the speakers will cause a delay in the output of the sound from that speaker. In other words, the speaker will sound like it is farther away. For example, setting the center speaker distance 3~6 feet (1~2 m) closer than the actual speaker position will create a fairly realistic sensation of being �inside� the screen. If you cannot obtain a satisfactory surround effect because the rear speakers are too close, setting the rear speaker distance closer (shorter) than the actual distance will create a larger soundstage. (1 foot corresponds to a 1 ms difference.) Adjusting these parameters while listening to the sound often results in much better surround sound. Give it a try!
Adjusting the speaker volume
Use the remote while seated in your listening position to adjust the volume of each speaker. Note
This receiver incorporates a new test tone with a frequency centered at 800 Hz for easier speaker volume adjustment.
Hooking and Setting Up the Speaker System
1 2
Press ?/1 to turn on the receiver. Press TEST TONE on the supplied remote. You will hear the test tone from each speaker in sequence. Adjust the volume level so that the volume of the test tone from each speaker sounds the same when you are in your main listening position. � To adjust the balance of the front right and front left speakers, use the front balance parameter in the LEVEL menu (see page 34). � To adjust the balance of the rear right and rear left speakers, use the rear balance parameter in the LEVEL menu (see page 34). � To adjust the volume level of the center speaker, press MENU </> to select the center parameter. Use +/� on the remote to adjust the level. � To adjust the volume level of the rear speaker, press MENU </> to select the rear parameter. Use +/� on the remote to adjust the level.
3
4
Press TEST TONE on the remote again to turn off the test tone.
Note
The test tone cannot be output when the receiver is set to 5.1CH INPUT.
z You can adjust the volume level of all speakers at the same
time
Rotate MASTER VOLUME on the receiver or press MASTER VOL +/� on the remote.
19
|
|
|
> |
|
