Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Text excerpt from page 9 (click to view)
125992054.qxp
2005-08-29
06:21
Page 9
Operating Sequence
Before using your tumble dryer for the first time, we recommend to place a few damp cloths inside the appliance and dry for 30 minutes. There may be dust inside a brand new tumble dryer. static zero. 9. If the laundry is not removed at the end of the cycle, the dryer performs an anti-creasing phase (duration: 30 minutes maximum). If you do not remove the laundry, the dryer will stop automatically at the end of the anti-creasing phase. The END, CLOGGED FILTERS and FULL TANK lights remain lit and the buzzer sounds every 10 seconds for 2 minutes. The light of the START/PAUSE button goes off and a flashing zero appears on the display. 10.Turn the programme selector dial to �0�; all the lights go out. The appliance is switched off. Remove the laundry. If you open and then close the door before turning the programme selector dial to �0�, all the lights corresponding to the phases making up the performed programme come on and the display shows the duration of the programme.
Drying
1. Connect the appliance. 2. Open the door (see picture).
P1149
P1108
3. Load the items one at a time, shaking them out loosely. 4. Close the door. Please check the laundry does not get caught between the door and filter. 5. Select the drying programme or time. The lights DRYING, COOLING and END come on. The light of the START/PAUSE button flashes and the display shows the duration of the programme. 6. If required, press the LOW TEMPERATURE button and/or the NO BUZZER button or the QUICK DRY button. 7. Select the DELAY START if required. The selected delay appears on the display for 2 seconds, then the duration of the selected programme is displayed. 8. Press the START/PAUSE button: the corresponding light stops flashing and drying starts. Only the DRYING light stays lit. If you have selected the DELAY START, the machine begins its countdown. If the programme selector dial is turned to another position, when the machine is running, the buzzer will sound, the programme phase indicator lights will flash and Err appears on the display. The drum turns alternately in both directions during drying. All drying programmes end with a 10 minute cooling phase (light COOLING is on). You may remove the laundry after this phase. The lights ENDE, CLOGGED FILTERS and FULL TANK illuminate and the buzzer sounds. The END, CLOGGED FILTERS and FULL TANK lights illuminate. The display shows a 9
After each use
� Clean the filters (see page 11). � Empty the water reservoir (see page 12). Important! If the drying programme has to be stopped before it reaches the end, we recommend that you turn the programme selector dial to position (cooling) and wait until the end of this phase before removing the laundry. This will avoid a build-up of heat inside the appliance. To do this first turn the dial to �0� and then to and depress START/PAUSE Button. Modifying the programme To change a programme which is running, first cancel it by turning the programme selector dial to �0�. Select the new programme and press the START/PAUSE Button.
