|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Ottimo manuale, grafica ferfetta invio rapidissimo. Altissimo livello!!!!!
;
Great PDF easy to read good info needed for replacment of belts and assembly and specs.
;
complete and unabridged very good quality
easy to download.
recieved in two days.
;
Awesome manual. Complete diagrams of all board assemblies as well as how to get to each part of the t.v. down to the individual screws and their locations. Get it.
;
perfect copy, im very satisfied, i was need the diagram over the powersupply and
the copy was very sharp
TK-3148
ADJUSTMENT / ��
Repair Jig (Chassis)
Use jig (part No.: A-10-4060-04) for repairing the TK-3148. Place the TX-RX unit on the jig and fit it with screws. The jig facilitates the voltage check and protects the module when the voltage on the flow side of the TX-RX unit is checked during repairs.
维修����壳�
使ç�¨æ�ºå£³ï¼�A-10-4060-04ï¼�ç»´ä¿® TK-3148ã��å°� TX-RX å��å��æ�¾ç½® å�¨æ�ºå£³ä¸�ï¼�并ä¸�æ�§ä¸�è�ºé��ã�� å�¨ç»´ä¿®è¿�ç¨�ä¸ï¼� å½�é��è¦�å�¨TX-RXå��å��ç��ç�µè·¯æ�¿ä¸�æ£�æµ�å�°ç�µå�� æ�¶ï¼�æ�ºå£³å�¯ä»¥æ�¹ä¾¿å�°è¿�è¡�ç�µå��æ£�æµ�ï¼�并ä¸�ä¿�æ�¤æ¨¡å��ã��
Battery Jig (W05-0909-00)
ç�µæ± 夹å�·ï¼�W05-0909-00ï¼�
+ Terminal (Red) ï¼�æ��端å�(红è�²) â�� Terminal (Black) ï¼�æ��端å�(é»�è�²)
Connect the power cable properly between the battery jig installed in the transceiver and the power supply, and be sure output voltage and the power supply polarity prior to switching the power supply ON, otherwise over voltage and reverse connection may damage the transceiver, or the power supply or both. Note: When using the battery jig, you must measure the voltage at the terminals of the battery jig. Otherwise, a slight voltage drop may occur within the power cable, between the power supply and the battery jig, especially while the transceiver transmits.
å�¨å®�è£�äº�ç�µæ± 夹å�·ç��æ� 线ç�µæ�¶å��æ�ºå��ç�µæº�ä¹�é�´è¿�æ�¥ç�µæº�ç�µ ç¼�ï¼�并确认è¾�å�ºç�µå��å��两æ��æ�¥é��å��ç�µæº�æ�¯å�¦ç¡®å®�æ�¥é��ï¼�å�¦å��è¿� é«�ç�µå��å��ç�µæ��è¿�æ�¥é¢ å��é�½æ��å�¯è�½æ��å��æ� 线ç�µæ�¶å��æ�ºæ��ç�µæº�æ��é�½ 被æ��å��ã��
注: å½�使ç�¨ç�µæ± 夹å�·æ�¶ï¼�ä½ å¿�é¡»æµ�è¯�ç�µæ± 夹å�·ç��两个ç�µæ��ç��ç�µ å��ã��å�¦å��å½�æ� 线ç�µæ�¶å��æ�ºæ�¶å��ä¿¡æ�¶ï¼�å�¨ç�µæº�å��ç�µæ± 夹å�·ä¹�é�´ç�� ç�µç¼�线ä¸�ä¼�å��ç��å¾®å°�ç��ç�µå��é��ã��
How to Remove the Cable
1. Gently draw out both sides of the connector lever uniformly in the direction of the arrow with tweezers. (CN303, CN304, CN305, CN306)
������
1ï¼� æ��ç�§ç®å¤´æ��示ç��æ�¹å��ï¼� ç�¨é��å�å��å��å�°å°�è¿�æ�¥å�¨æ�¨æ��ç��两侧æ©� å¼�ã�� ï¼�CN303, CN304, CN305, CN306ï¼�
Tweezers é��å�
2. Gently rise up the connector lever in the direction of the arrow with a fine regular screwdriver or tweezers. (CN301, CN302, CN400)
Regular screwdriver 常����
2ï¼� 使ç�¨å¸¸ç�¨ç��å°�å��æ�¹é�¥ï¼� æ��ç�§ç®å¤´æ��示ç��æ�¹å��å°�å¿�å�°æ�¬èµ·è¿�æ�¥ å�¨ç��æ�¨æ��ã�� ï¼�CN301, CN302, CN400ï¼�
Flat cable �平�� Lever ��
38
|
|
|
> |
|
