|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Manual is actually a pack of schematics, good quality pictures.
;
Great service. Manual delivered at a great price. Reliable delivery service. They have a great selection. A recommended service!
 ;
I used your service and I found myself well I need service manual teac v plate 770 and I was able to access and remove the belt that erno routes. thanks I recommend it to all
;
At first I thought there had been a mix up as I required the service manual for the cassette unit and the one supplied was for the CD unit. However when I scrolled further down I realised that both had been scanned together! This enabled me to dismantle and repair the cassette unit as intended and I also have a copy of the manual for both the CD and graphic equaliser units should I ever need them. Thanks very much for a great service.
;
Excelent service, the manual is complete, very cheap and fast
Alberto
TK-860HG/862HG
REALIGNMENT
Clone Mode
Programming data can be transferred from one radio to another by connecting them via their modular microphone jacks. The operation is as follows (the transmit radio is the master and the receive radio is the slave). 1. Turn the master TK-860HG power ON with the [ ] key held down. If the password is set to the TK-860HG, the TK-860HG displays �CLN LOCK�. If the password is not set, the TK-860HG displays �CLONE�. 2. When �CLN LOCK� is displayed, only the [CH / ] key and [SCN], and [0] to [9] keys can be accepted. When you enter the correct password, and �CLONE� is displayed, the TK-860HG can be used as the cloning master. The following describes how to enter the password. How to enter the password with the microphone keypad; If you press a key while �CLN LOCK� is displayed, the number that was pressed is displayed on the TK-860HG. Each press of the key shifts the display in order to the left. When you enter the password and press the [SCN] key, �CLONE� is displayed if the entered password is correct. If the password is incorrect, �CLN LOCK� is redisplayed. How to enter the password with the [CH / ] key; If the [CH / ] key is pressed while �CLN LOCK� is displayed, numbers (0 to 9) are displayed flashing. When you press the [SCN] key, the currectly selected number is determined, and the display shifts to the left. If you press the [SCN] key after entering the password in this procedure, �CLONE� is displayed if the entered password is correct. If the password is incorrect, �CLN LOCK� is redisplayed. Power on the slave TK-860HG/862HG. Connect the cloning cable (No. E30-3382-05) to the modular microphone jacks on the master and slave. Press the [SCN] key on the master while the master displays �CLONE�. The data of the master is sent to the slave. While the slave is receiving the data, ��PC�� is displayed. When cloning of data is completed, the master displays �END�, and the slave automatically operates in the User mode. The slave can then be operated by the same program as the master. The other slave can be continuously cloned. When the [SCN] key on the master is pressed while the master displays �END�, the master displays �CLONE�. Carry out the operation in step 4 to 6.
PTT/RXD GND REMOTE/TXD 8
Clone cable E30-3411-05 (TK-860HG � TK-360G/370G)
1
MBL PSB GND PTT/TXD ME MIC HOOK/RXD CM
8 1
3.
Cloning cable (E30-3382-05)
Fig. 1
4. 5. 6.
7.
Note :
You can clone the programmed data between the transceiver frequency version must be same.
4
|
|
|
> |
|
