|
|
|
Who's Online
There currently are 5762 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was very clear and contained all the information I was looking for. My dishwasher is working again because of this servicemanual!
;
Quality scan, great manual. I solved my problem with this manual.
 ;
The AKAI 1720 model reel to reel tape recorder described in this Manual is quite an old unit - circa late 1960's. As a consequence, the description of the mechanical details - and adjustments thereof - is quite critical. The manual does this quite well. The schematics are also well presented and have detailed PCB overlays. Probably the only negative is that some half-tone detail has been lost from the original manual as it has been scanned in simple B&W.
;
Perfect source for service manuals: fast and professional transaction; high quality, perfect readable and largely scaleable PDF; complete schemes, diagrams and spare part list. Tnx a lot, cu again!!!!
;
I got your link from a friend and I must say that I am really satisfied with your service. Specially this B&O manual I didn't find anywhere on the web... but you could deliver it :-) . You deliver very fast and the copy is of good quality. So your webpage is bookmarked. Thanks
Chapter 6
OPERATION OF POWER SUPPLY
1. Transition from AC ON to Standby mode When the AC source is supplied to this power circuit, the voltage rectified by D101 and smoothed by C105 is supplied to VH pin of IC102 through R125. VCC pin voltage of IC102 rises by current supplied to VCC pin through VH pin. And then, IC102 starts up and the DC/DC converter begins to operate. (6V, 14V and 17V start up.) * This DC/DC converter is a PWM switching circuit, which is composed of IC102, T201 and Q103 mainly. 2. Transition from Standby mode to Typical Operation mode When the level of ST/OP pin in the connector CN201 is Low or open, only the DC/DC converter is in the switching operation. Each output does not have the on/off control which works solo, except primary 16V line. The voltage level of primary 370V line becomes voltage after smoothing through bridge rectifier circuit. (e.g. Input: 100Vac, Output: approx. 140Vdc) This status is standby mode. When the level of ST/OP pin in the connector CN201 is High, Q105 is turned on through a photo-coupler PC103, and then the primary 16V source is supplied to the Ballast and IC101 of PFC circuit. Because VCC voltage of IC101 reaches threshold level of starting voltage, IC101 starts up activity and the PFC circuit begins to operate. The voltage level of primary 370V line becomes approximately 370V which is stable against variation of AC input voltage. * ST/OP pin is a pin to control for switching mode between standby and typical operation. 3. Protection against abnormal condition If Overvoltage or overheat or overload happens, the DC/DC converter stops the switching operation by putting IC102 into the latch mode. Every output (They are primary 16V, secondary 6V, 14V and 17V.) of the DC/DC converter is turned off, and this is maintained. PFC circuit stops the switching operation because +16V line which is power source for the control IC of PFC is turned off. The voltage of 370V line varies to voltage that rectified the AC source. (i.e. The boost stops.) About the latch mode of IC102 In normal operation, CS pin voltage of IC102 is clamped by an inside 4V zener diode. Externally forcing CS pin voltage to increase to the threshold voltage, 8.2V, for the latch mode allows the IC102 to stop its operation for protection. When CS pin voltage reaches to 8.2V, the inside source in IC102 is turned off, and OUT pin (for gate drive of FET in the DC/DC converter) is set to the Low level. Then, the start-up circuit is activated again, and VCC voltage is held at approximately 22V. This status is the latch mode of IC102. The latch mode is maintained as long as supply to VCC pin continues. It takes time for the latch mode to be rest because charged C105 voltage is applied to the VH pin even if IC102 have changed to the latch mode. Cutting off the input voltage decreases VH pin voltage, supplying no current to the VCC pin. Thereafter, the latch mode is reset when VCC drops below the OFF threshold level, 8V min.
6�10
|
|
|
> |
|
