KORG TRITON
Quick Start

TRITON Extreme EasyStart

2.

Press the SAMPLING key

Press the �Input Setup� tab

Press the upper-right � popup, and then Press �OK�. All

press the scroll bar to display �Auto Sampling Setup� sampling parameters will now be automatically set up. 3.

Press �REC Audio Input�, and then set �Source

Audio� to �Analog�, �Stereo� to �Mono-1�, �Save to� to �RAM� and �IFX� to �Off�

Now to change the �Trigger� setting, so that sampling will begin when the input audio exceeds the set level: Press the �Trigger� begins. popup and set this to �Threshold� Set the �Level� to �-30 dB�, and then set �Pre-Trigger� to �005 ms�, in order to capture the very beginning of the sample when sampling

4.

Set the recording level with the REAR PANEL LEVEL knob � speak into the mic and adjust the level as high as possible without allowing the �ADC OVERLOAD !!� warning to appear in the display as possible, avoiding the �CLIP!!� warning. Press the SAMPLING REC key, and then adjust the �Recording Level� with the VALUE SLIDER � set this as high

5.

With the SAMPLING REC key still lit, press the SAMPLING START/STOP key, and then speak into the mic, saying the word �This� When finished speaking, press the SAMPLING START/STOP key to stop sampling. Press C2 on the keyboard to hear your new sample.

6.

Now to make settings for individual samples across the keyboard (multisample): Press the �Preference� tab and set the �Zone Range� to �1 key� �Recording� tab Un-check the �Auto Loop On� checkbox, and then press the Press the �Create� button in the display to Press SAMPLING START/STOP Set �OrigKey� and �TopKey� to �C2� - the easiest way to set this is by holding down

the ENTER key and pressing the C2 key on the keyboard set a new key index (�C#2�). 7.

Press the SAMPLING START/STOP key and say the word, �is� display moves to the next key after you press �Create�.

again to stop sampling, and then press the �Create� button in the display. Note that the �keyboard� 8. Repeat the previous step 3x, to record three more samples, sampling �the�, �Triton�, and finally �Extreme� �That�s it! Now play the keyboard: play each note (half-step) from C2 to E2, and you�ll hear the sampled words, �This is the TRITON Extreme�.

Tip:

You can use the above procedure with any external audio source, such as a drum machine � to create a new multisampled drum kit!

Continue by sampling through one of the Extreme�s Insert Effects�
9. Press the �Input Setup� tab choose �IFX1� the ENTER key). 10. Press the MENU key, and then press �P8: Insert Efffect� the �OFF� toggle button in the �IFX1� box �ON� Reverb Hall� for IFX1 Press the �Insert FX� tab, and press to set Press to highlight �000:No Effect�, and select �052: Press the SAMPLING REC/WRITE key Speak In the �Input 1� field, press the popup by �BUS(IFX) Select� and Set �Pan� to �C064� (use the numeric keypad and enter �64�, followed by pressing

Speak into the microphone to hear the effect being applied.

11. Press the EXIT key, then press the �Recording� tab into the mic and adjust the recording level as needed.

12. Press the SAMPLING START/STOP key, and then speak to sample �Create� button to set a new key index.

Press SAMPLING START/STOP Press the

to stop sampling. The new sample will playback on key F2 � the next available index

Continue by sampling though the tube and using Valve Force technology�
13. Press the VALVEFORCE ON/OFF key (it will light) FORCE� (Tube)� Press the MENU key, and then select �P9: VALVE Set �Pan� to �C064� and �BUS� to �3

Use the DIAL to set �Placement� to �Insert (Use 3/4 BUS)�. Press the �Recording� tab.

14. Press the EXIT key, and then press the �Input Setup� tab

15. Press the REALTIME CONTROL key until the LED lights in the VALVEFORCE section, and as you speak into the mic, work with the CONTROL knobs to set Valve Force parameters to suit.

8