|
Who's Online
There currently are 5945 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
Alignment and Adjustments
3-3-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so external degaussing after moving the TV should be unnecessary. However, the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 10 Minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.
3-3-4 FOCUS Adjustment
1. Input a black and white signal. 2. Adjust the tuning control for the clearest picture. 3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
3-3-5 B+ Line Check
There are 3 power modes : 1. �A� : When AC power supply is connected ; � Stand-By� mode. 2. �B� : When � Set Power-ON� button is pressed. 3. �C� : Driven by FBT. Each voltage is marked on its lead-in wire. ( )
3-3-3 High Voltage Check
CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply must be set to either +135V or +125V (for 20� screen). Conditions : Full color bar input and normal picture level. 1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. The high voltage must not exceed 29.5KV. 4. Adjust the Brightness and Contrast controls to both extremes. Ensure that the high voltage does not exceed 29.5KV under any conditions. SIZE MAX H-VOLTAGE 27.5KV 29.5KV 29.5KV 29.5KV 21�± 1 25� 29� 29�± 1
3-3-6 F/S (Fail Safe) Circuit Check
1. The failsafe circuit check is the final step after servicing. 2. Turn the power switch on and adjust the screen for �Normal�. 3. Temporarily short Pin R and Pin X on the chassis (RX05, RX04). Sound and picture will disappear. 4. The TV should remain in this state. This shows that the failsafe circuit is working properly. 5. To restore picture and sound, temporarily turn off the AC power supply. After about 30 seconds, switch power ON.
3-6
Samsung Electronics
|
|
|
> |
|