|
|
|
Who's Online
There currently are 6003 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I am very happy regarding the online purchase of this manual from Owner-Manuals.com as with this I could set right my Denon CD player and Amplifier.
I once again sincerely thank them for the prompt service which was rendered to me.
N. Shanker
;
More than pleased with my prurchase, very good product for the price.
;
Manual-link came 30 minutes after having paid for an extremely rare (40 years old) item (sony icr-120) and helped me to get the radio rework again. So really good help for me, fast and reliable delivery and -taken that into consideration- a very reasonable price for that service. So thanks again! Mike, Germany
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
Final check after repair
3.7
Final check after repair
Final check after repair The �nal check after repair, describes the activities that are needed to ensure the product will be returned in perfect condition to the customer. The contents is: AC leakage test. Check product information. Restore the setup and check connections, picture and sound. Final cleaning of the product. PIN-code setting.
AC leakage test
The scope of the test is, to check the antenna terminals and other exposed metal parts for AC leakage. 1. 2. 3. 4. Remove the line cable from the AC source (the wall outlet). Place a jumper across the two AC plugs prongs. Use a multi-meter, set for measurements in the ohm-area. Place one lead from the multi-meter on the AC plug and place the other lead on each of the exposed metal parts, that is antenna connections and other exposed metal parts on the rear panel of the product. The resistance during these measurements must be of 1 Mega Ohm or more. If resistance is below 1 Mega Ohm, this indicates an abnormal situation and corrective actions must be taken.
5.
Insulation test Each set must be insulation tested after having been dismantled. Make the test when the set has been reassembled and is ready to be returned to the customer. Flashovers must not occur during the testing procedure! Make the insulation test as follows: Short-circuit the two pins of the mains plug and connect them to one of the terminals of the insulation tester. Connect the other terminal to ground on the aerial socket. NOTE! To avoid damaging the set it is essential that both terminals of the insulation tester have good contact. Slowly turn the voltage control of the insulation tester until a voltage of 1.5 kV and max. 10mA is obtained. Maintain that voltage for one second, then slowly turn it down again. Insulation test at the customer Remove the mains cable from the wall outlet. Place a jumper across the two AC plug prongs. Use a multi-meter, set for measurements in the Ohm-area. Place one lead from the multi-meter on the AC plug and place the other lead on ground at the Power Link plug. The resistance during this measurement must be of 1 Mega Ohm or more. Resistance measured below 1 Mega Ohm indicates an abnormal situation and corrective action must be taken.
|
|
|
> |
|
