|
|
|
Who's Online
There currently are 5707 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
;
This SM is quiet scarce and hard to find it is an excellent Service manual, very clear to read and to print schematics and diagrams, Hi quality, Complete manual with no pages missing. I am very pleased with the manual and the fast service I have received. Great place to shop.
Good luck finding you manual...
Alignment and Adjustment
a. ACE HEAD HEIGHT ADJUSTMENT 1) Run the alignment tape (Color bar) in the playback mode. 2) Observe surface of the audio head using a dental mirror. 3) Turn screw (C) clockwise or counterclockwise until the gap of lower tape edge and the lower edge of the control head is about 0.25mm. (Refer to Fig. 5-6 and 5-7)
b. ACE HEAD TILT ADJUSTMENT 1) Playback a blank tape and observe the position of the tape at the lower flange of tape guide. 2) Confirm that there is no curl or wrinkle at the lower flange of tape guide as shown in Fig. 5-8 (B). 3) If a curl or wrinkle of the tape occurrs, slightly turn the screw (A) tilt adjust on the ACE head ass�y. 4) Reconfirm the ACE head height.
(A) (B)
SCREW (A) TLIT ADJUST
SCREW (C) HEIGHT ADJUST WRINKLE
X-POSITION ADJUSTING SLIT SCREW (B) AZIMUTH ADJUST
SCREW (D) X-POSITION LOCKING
(BAD)
(GOOD)
Fig. 5-6 Location of ACE Head Adjustment Screw
Fig. 5-8 Tape Guide Check c. AUDIO AZIMUTH ADJUSTMENT
AUDIO HEAD VIDEO HEAD
0 ~ 0 .25 mm CONTROL HEAD
1) Load alignment tape (Mono scope) and playback the 6KHz signal. 2) Connect channel-1 scope probe to audio output test point (TP302). 3) Adjust screw (B) to achieve maximum audio level. (See Fig. 5-6) d. ACE HEAD POSITION (X-POINT) ADJUSTMENT
Fig. 5-7 ACE Head Height Adjustment
1) Playback the alignment tape (Color bar). 2) Press the �SW703� button on Main PCB to set the adjustment mode. (See Fig. 5-2) 3) Press the �5� button of remote control then adjustment is operated automatically. (See Fig. 5-1) 4) Connect the CH-1 probe to TP303 (Envelope) the CH-2 probe to TP601 (H�D switching pulse) and then trigger to CH-1. 5) Insert the (-) driver into the X-Point adjustment hole and adjust it so that envelope waveform is maximum. 6) Turn the Power off.
Toshiba
5-5
|
|
|
> |
|
