|
|
|
Who's Online
There currently are 6005 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The service manual is really great - thanks to it I was able to install the laser unit and thus "save" my CD-player, which seemed to be impossible before I had the manual.
;
Downloaded the Service manual OK of the Technics Piano and have now repaired it and its going fine. Excellant; thank you for the fine servce. A.M
 ;
This site is working fine! Did buy a manual for SX-EX25L and after a while I could download it and fix the problem. Nice and easy!
;
Complete manual as pdf-file in very good quality. Very helpful and fast availability.
;
Complete service manual in very good scanning quality with all schematic and PWB graphics as well as assembly & maintenance instructions. A slight drawback is that the rastering of the PWB graphics sometimes makes it a bit difficult to follow fine traces, but no showstopper.
VC-AA350A/L/M/W VC-AA352W,AA360A,AA370A VC-AA550A/L/W,AA560A,AA570A Note: Whenever replacing the reel disk, perform the height checking and adjustment.
Master plane Reel disk height adjusting jig
Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow longtime measurement.
10 ± 0.2mm
Reel disk
A
Mechanism chassis
4-7 CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN REWIND MODE
� Remove the cassette housing control assembly. � After short-circuiting between TP803 and TP802 provided at main PWB, plug in the power cord. � Setting 1. Set a torque gauge to zero on the scale. Place it on the supply reel disk. 2. Press the rewind button. 3. To calculate the remaining capacity, slowly rotate the take-up reel disk, and then shift it into the rewind mode. � Checking 1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CCW direction. 2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).
Torque gauge
B
Reel disk
Figure 4-5.
4-6 CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN FAST FORWARD MODE
� Remove the cassette housing control assembly. � After short-circuiting between TP803 and TP802 provided at main PWB, plug in the power cord. � Setting 1. Set a torque gauge to zero on the scale. Place it on the take-up reel disk. 2. Press the FF button. 3. To calculate the remaining capacity of the play back mode, slowly rotate the supply reel disk, and then shift it into the forward mode. � Checking 1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CW direction. 2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).
Torque gauge
CCW
30mN·m (306gf·cm) or more
30 The gauge is held at its maximum value. (Red mark)
Supply reel disk 30mN·m (306gf·cm) or more CW
The gauge is held at its maximum value. (Red mark)
Idler ass'y
Figure 4-7. � Adjustment 1. If the rewind winding-up torque is less than the specified value, clean the capstan D.D. pulley, reel belt, and limiter pulley with cleaning liquid, rewind again, and check the winding-up torque. 2. If the winding-up torque is still out of range, replace the drive belt.
Idler ass'y
Figure 4-6. � Adjustment 1. If the FF winding-up torque is less than the specified value, clean the capstan D.D. pulley, reel belt, and limiter pulley with cleaning liquid, and check again. 2. If the torque is less than the set value, replace the reel belt.
12
|
|
|
> |
|
