|
|
|
Who's Online
There currently are 5647 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very pleased with manual except that a few more details in the drawings might make the job (not yet done, tut-tut) easier. Should be adequate though. Actually I didn't have to pay for this anyway as I was given credit for another item that wasn't quite complete. Good service, then.
;
Very useful manuals, somewhere graphics not very clear!
 ;
A great manual; it contained all the information I required and allowed me to restore the receiver to full working condition!
;
Very good expirience with owner-manuals.com.
5 Stars; In future if necessary, i´ll download manuals on this site.
;
Hi - happy with what I received but not quite what I wanted - my fault I assumed that service manual would also include operational instructions which is what I needed - all I needed to know was how to turn the radio - thanks
The operating instructions mentioned here are partial abstracts Operating Instruction Manual remein as in the manual.
http://cxema.ru
SECTION 1 from the Operating Instruction Manual. The page numbers of GENERAL
Warning on power connections
AC IN
Precautions Identifying parts and controls
Use of the stand
position.
� Use the supplied cord. If you use a different power cord,
Insert supplied stand into groove to adjust angle of the monitor. You can use stand in either the vertical or horizontal See the pages in parentheses for further details. (Model HMDA200 is used for illustration purposes.)
be sure that it is compatible with your local power supply. Front Rear For customers in the UK If you monitor in UK, be sure to use the supplied UK power cable.
Example of plug types
MENU
100 120 200 to for 240 V AC only
� Before disconnecting the power cord, wait at least 30 seconds
after turning off power to allow static electricity on the screen�s surface to discharge.
� After power turned on, the screen is demagnetized
(degaussed) for about 5 seconds. This generates a strong 1 Control button 9) 4 Video input connector (HD15) (page 6) magnetic field around screen which may affect data stored The control button is used to display the menu and make This connector inputs RGB video signals (0.700 Vp-p, on magnetic tapes disks placed near monitor. Be sure adjustments to the monitor, including brightness contrast positive) and sync signals. adjustments. keep magnetic recording equipment, tapes, and disks away 2 1 (power) switch and indicator (pages 6, 13, 16) 6 7 8 9 10 You can put a photo frame or CD case in the groove. This button turns the monitor on and off. The power indicator GB The equipment should be installed near an easily accessible 11 12 13 14 15 lights up in green when the monitor is turned on, and either outlet. flashes green and orange, or lights up in orange when the Pin No. Signal monitor is in power saving mode. Installation
from monitor. Use of the groove on top (HMD-A200 only) 1 2 3 4 5
1-1
11 ID (Ground)
1 Red
Do not install monitor in the following places: 3 AC IN connector (page 6) 2 Green � on surfaces (rugs, blankets, etc.) or near materials (curtains, This connector provides AC power to the monitor. (Composite Sync on Green) draperies, etc.) that may block the ventilation holes � near heat sources such as radiators air ducts, or in a place 3 Blue subject to direct sunlight 4 ID (Ground) � in a place subject to severe temperature changes � in a place subject to mechanical vibration or shock Note � on an unstable surface 6 Red Ground Never use the slit for any other purpose. � near equipment which generates magnetism, such as a 7 Green Ground
5 DDC Ground*
Use of the headphones� hook (HMD-A100 only) transformer or high voltage power lines
� near or an electrically charged metal surface Insert supplied hook into one of holes (ten on both the left
8 Blue Ground
Maintenance 10 Ground
and sides) on either left or right side of the monitor. 9 �
� Clean the screen with soft cloth. If you use a glass cleaning Side
liquid, do not use any type of cleaner containing an anti-static solution or similar additive as this may scratch the screen�s 12 Bi-Directional Data (SDA)* coating. 13 H. Sync
� Do not rub, touch, tap surface of the screen with sharp or
abrasive items such as a ballpoint pen or screwdriver. This type of contact may result in a scratched picture tube. 15 Data Clock (SCL)*
14 V. Sync
� Clean the cabinet, panel and controls with a soft cloth lightly
* DDC (Display Data Channel) is a standard of VESA. moistened with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder solvent, such as alcohol or benzene.
5 USB (universal serial bus) downstream connectors (page 7) monitor. 6 USB (universal serial bus) upstream connector (page 7) Use this connector link the monitor to a USB compliant computer.
Transportation Never hang heavy objects from hook other than the headphones. Use these connectors link USB peripheral devices to the
Note
When you transport this monitor for repair or shipment, use the original carton and packing materials.
4 5
|
|
|
> |
|
