|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
You can fully trust on this one!
All the schematics are very crear an in one piece per page
;
I have never bought a service manual which is as competely readable as this althogh it was a scanned pdf. Thank you for this succesful manual also cheaper than other sites.
;
Thanks for a very good and readable servicemanual. Just what I needed as a "dinosaur technician". I really recommmend this site and will come back.
Åsbjörn
;
The manual I purchased was just what I needed. I was glad to find a site where I can find so many manuals on a wide variety of products.
;
The best diagram that I used in a long time. Everything was right on te money. It was easy and fast. Iwoiuld but again when I need a service manual.
Alignment and Adjustment
5. AUTO IRIS 1) Camera �E-E�, 3100°K gray-scale chart. 2) Video(output) jack and AF MICOM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the �DATE/TIME(MODE UP)/ TITLE (MODE DOWN)� button so that the OSD state is �OCE. IRIS XX XX�. 5) Press �MENU/ENTER(CONFIRM)� Button. 6) Then, the micro process will work; - IRIS open, IRIS control MAXIMUM Value found. - IRIS close, IRIS control minimum Value found. - Store the MIN/MAX data to mode 0BE, 0BF and mode 0A3, 0A4. 7) The OSD shows �O.K�.
Center of white level H
b-2. Press �MENU/ENTER(CONFIRM)� button so that the white vector moves to the center on screen of the vectorscope. b-3. During the control W/B outdoor, OSD shows �0CF, AWB xx 01�. The OSD shows �OK!�. b-4. Store the data to mode 053, 054, 055 and 056.
Match the white luminance point with the black luminance point
100IRE
Match the white luminance point with the black luminance point
Optical black level
40US
6. Auto white balance 1) Camera �E-E�, 3100°K/5100°K gray-scale chart. 2) Video(output) jack and AF MICOM. 4) Connect vectorscope input jack to video(output) jack. 3) Press the �DATE/TIME(MODE UP)/TITLE (MODE DOWN)� button so that the OSD state is �OCF. AWB XX XX�. a. W/B Indoor a-1. Aim the camera at a 3100°K gray-scale chart illuminated at 1500 to 2000 lx. (40us) a-2. Press �MENU/ENTER(CONFIRM)� button so that the white vector moves to the center on screen of the vectorscope. a-3. During the control W/B indoor, OSD shows �0CF, AWB xx 00�. The OSD shows �OK!�. b. W/B Outdoor b-1. Aim the camera at a 5100°K gray-scale (or, 3100°K+C16 filter) chart illuminated at 1500 to 2000 lx. (40us)
7. Pre white balance (I) 1) Camera �E-E�, 3100°K gray-scale chart. 2) Video(output) jack and AF MICOM. 3) Connect vectorscope input jack to video(output) jack. 4) Press the �DATE/TIME(MODE UP)/TITLE (MODE DOWN)� button so that the OSD state is �137. XX XX.� (R-Y axial) 5) Aim the camera at a 3100°K gray-scale chart illuminated at 1500 to 2000 lx. 6) Adjust the �C/RESET(DATA UP)/Z/RTN (DATA DOWN)� button so that the white vector moves to the R-Y axial on screen of the vectorscope. Note : Bright dot shifts after the confirm button is pressed.
5-20
Samsung Electronics
|
|
|
> |
|
