|
|
|
Who's Online
There currently are 5420 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
;
Nothing wrong with the manual or the delivery - came to me the same day I ordered it. But afterwards I realized that I ordered the wrong manual. Probably better with the Quick start - version. So maybe it would be better if we could see a list with inhold for each manual before ordering?
 ;
Bought T4850 High End Tuner a few years ago, but i didn't know where all the buttons were used for. So i purchased the owners manual. Perfect! Just what i needed.
Controlling the rest of your system
10
3 Use the number buttons to enter the preset code. You can find the preset codes on page 64 (VSX-D712) and page 65 (VSX-D812/912). The LED blinks again after you enter the code. If the correct code has been input the power of the component being input will turn on or off. The power of the component being input will only turn on or off if that component is able to be turned on directly by remote control. � You can only input a code for the component type written on each MULTI CONTROL button (except RECEIVER and TUNER). � Even if you don�t input a preset code for the TV (TV/SAT MULTI CONTROL button) you will be able to control your TV using the dedicated TV CONTROL on the remote if you have assigned it to the TV CONT button. � You may not be able to use a particular code even if it is listed on page 64. � The remote control buttons will not be able operate other equipment unless preset with the method above. 4 Repeat steps 2 through 3 to try a different code, or to enter a code for another component you want to control. 5 When you�re done, press RECEIVER.
nent (for example , , or other operation buttons). This can also be used to program additional operations (buttons not covered in the presets) after assigning a preset code. 1 While pressing the RECEIVER button, press and hold the 2 button. The LED blinks. 2 Press the MULTI CONTROL button for the component you want to control. The LED lights. � To exit or cancel press RECEIVER. 3 Point the two remote controls towards each other about 2�5 cm apart then press the button that will be doing the learning on this receiver�s remote control. The LED blinks rapidly.
2 � 5 cm
4 Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver�s remote control. If the operation has been learned successfully, the LED on this receiver�s remote will blink once then light steadily. If for some reason the operation hasn�t been learned the LED will blink for three seconds and then light steadily. If this happens, keep pressing the (teaching) button as you vary the distance between the two remotes, until you see the the LED light steadily. If there is not enough memory for this button to be learned by the remote, the LED will blink twice and the operation will be canceled. 5 To program additional signals for the current component repeat steps 3 and 4. To program operations for another component exit and repeat steps 1 through 5.
English Italiano Français Deutsch Nederlands Español
Programming signals from other remote controls
VSX-D812/D912 only If the preset code for your component is not available, or the available preset codes do not operate correctly, you can program signals from the remote control of another compo-
59
En
|
|
|
> |
|
