BAUKNECHT WA 2700-B
Quick Start

Overview of consumption data GB
approx. Note: The programme stops to at time the �Rinse Hold� button light flashes.

Temperature Max. Load Water Energy Programme Duration

(°C) (kg) (l) (kWh) (hour: minutes)

Cotton 95 5.0 54* 1.60 1 : 55

Coloured Cotton 60 5.0 49 0.95 2 : 00

Coloured Cotton 40 5.0 49 0.55 1 : 45

Synthetics 60 2.5 55 0.70 1 : 30

Synthetics 40 2.5 50 0.50 1 : 15

Terminate the �Rinse Hold� option: � Press �Rinse Hold� button again; the programme will terminate automatically with final spin cycle for the present wash programme. � If you do not wish spin clothes, turn programme selector knob to the drain programme and press the �Start/Pause� button again. �Spin Speed Reduction� button

Programme 3.0 35 0.40 0 : 30 � Every programme has an automatic predefined maximum spin speed.

Delicates 30 1.5 50 0.50 0 : 45 � Press the button to set another spin speed.

Wool 1.0 50 0.50 0 : 40 � If spin speed �0� selected, the final spinning cancelled. The water is drained

Handwash cold 1.0 0.20 0 : 35 out only.

Prewash cycle increases programme duration by approximately 15 min. Consumption values were

PROGRAMME START measured normalized conditions in compliance with Standard IEC 60 456. The data on the �Energy
Open tap and press button. The pilot lamp of the �Start/Pause� Label� refer to programme �Coloured Cotton 60 °C�. Consumption data in the home may vary with

respect values table relation to water supply pressure and temperature, load button lights up. The indicator lamps show sequence reached in the programme. After and type of wash. starting programme, the sequence indication runs from left to right through Wash, Rinse, * To reduce temperature, some cold water is added at end of the main wash cycle, Spin. When sequence of programme is finished the corresponding lamp goes out. before pump drains the water out.

DOOR LOCK
for adding further laundry. Add detergent as described chapter �Detergent and Additives� in the booklet. The door can be opened when �Door Free� indication is shining. 1. Turn selector knob to the desired programme and temperature.

ADD DETERGENT, CLOSE DOOR AND SELECT THE PROGRAMME During first 15 minutes of cotton and synthetics programmes the door can be opened

� The pilot lamp of the �Start/Pause� button is flashing.

PROGRAMME END 2. The programme sequence and the predefined spin speed indication corresponding to
� All lights of the programme sequence indication are off. the selected programme lights up. A short audible tone sounds three times. 1. Turn programme selector to the � � position. PRESS ANY DESIRED OPTION BUTTON(S). The pilot lamp lights up. 2. Turn water supply tap off. An audible tone sounds if the combination of programme, additional options and 3. Open door and unload the machine. temperature is not possible. Unsuitable combinations of options are deselected

CHANGE THE AND OPTIONS AFTER PROGRAMME START
1. Press �Start/Pause� button to pause the programme. The light flashes. 2. Select the new programme, any options and another spin speed if you want it. 3. Press �Start/Pause� button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.

automatically. �Prewash� button � Only for heavily soiled loads (for example sand, granular dirt) sensible. The cycle time increases by approximately 15 min. �Intensive Rinse� button � A further rinse cycle is added. � This option is particularly suitable for areas with very soft water washing baby linen and helps people with allergies. TO CANCEL A PROGRAMME BEFORE THE END �Rinse Hold� button 1. Press �Start/Pause� button to pause the programme. The light flashes. � The laundry remains in last rinse water without progressing to the final spin cycle 2. Set the programme selector to �Drain�. The spin indicators show �0�. to avoid creasing and prevent colours from changing. 3. Press �Start/Pause� button to start the drain programme. � This option is particularly recommended for the programme �Synthetics� or �Delicates�. � This function is particularly useful if you want postpone spinning to a later time.