|
|
|
Who's Online
There currently are 6003 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very well done!!!!! congratulations. It was a bit longer than usual the wiating time even if it was on time (in 24 hours).
;
Last week I bought a second hand BAUKNECHT TRK4850 DRYER. It is a professional machine with many programs and switch options. I feared it would be a huge quest to find a manual. I was delighted when I found owner-manuals.com. After payment I received the file to download the next day already. The quality is great. I am very happy. Thanks!
but kindly the distributions of the operating programs not find in the owners manual,can you help me to understand the operating programs instructions thank you
;
Very good copy, very readable and easy transaction as always.
;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
4gb05103.fm Page 9 Thursday, August 14, 2003 11:57 AM
Worktop for built-under models
The appliance must only be installed beneath a continuous worktop. The appliance may only be built under using the intermediate cover panel of the UBS base set. This can be obtained from specialist dealers or After-Sales Service.
1. Pull out the power plug. 2. Remove the worktop fixing screws on the rear of the appliance. 3. Slide the worktop fully backwards, lift it up and remove it. Install the base set following the relevant instructions.
4. Refit the fixing screws and tighten them. 5. Connect the appliance to the electricity.
Connect the water inlet hose
For models with straight hose:
1. Insert the mesh filter (already premounted on the hose end or included in the accessories) into the threaded tap coupling. 2. Carefully screw the water inlet hose connection onto the tap by hand. 3. Make sure there are no kinks in the drain hose. 4. Turn the tap on fully and check that the joints at the washing machine and the tap are watertight.
If the hose is too short, replace it with a suitable length of pressure resistant hose (1000 kPa min, EN 50084 approved type). Check the hose regularly for brittleness and cracks and replace if necessary. The washing machine can be connected without a nonreturn valve.
If the flexible hose is too short, replace it with a 3 m Water Stop hose (available from After-Sales Service or from your dealer). This replacement is only to carried out by a trained electrician. The appliance must not be connected to the mixing tap of an un-pressurized water heater. Depending on the design, the inlet hose and the plastic enclosure at the tap connection contain electrical components. Do not cut the hose and do not immerse the plastic enclosure in water. Isolate the appliance from the mains immediately if the hose is damaged.
For models with Water Stop hose:
1. Screw the threaded connection with the mesh filter onto the tap. 2. Turn the tap on fully and check that the tap joint is watertight.
Connect the water drain hose
1. Connect the drain hose to the siphon or hook it over the edge of a sink by means of the �U� bend supplied. 2. Make sure there are no kinks in the drain hose. 3. Secure the hose so that it cannot fall down while the appliance is running. Small hand basins are not suitable. To make an extension, use a hose of the same type. Secure the connections with clips. Max. Overall drain hose length: 2.50 m Maximum drain height: 1.25 m
Depending on the model, the drain hose can be:
A. installed in the upper part of the washing machine. In this case the hose can be undone from both fastenings. B. Installed in the lower part of the washing machine.
Important:
In this case never undo the hose from the right-hand fastening, otherwise the appliance could overflow when operating.
9
|
|
|
> |
|
