BAUKNECHT WA 7740-NORDIC
Quick Start

GB Overview of consumption data

Temperature Max. Load Water Energy Programme Duration Note: The programme stops to at time the �Rinse Hold� button light flashes.

Programme approx. Terminate the �Rinse Hold� option:

(°C) (kg) (l) (kWh) (hour : minutes)

Cotton 95 5.0 44* 1.60 1 : 55 final spin cycle for the present wash programme.

� Press �Rinse Hold� button again; the programme will terminate automatically with

Coloured Cotton 60 5.0 39 0.95 2 : 00 � If you do not wish spin clothes, turn programme selector knob to the drain

Coloured Cotton 40 5.0 39 0.55 1 : 45 programme and press the Start/Pause � � button again.

Synthetics 60 2.5 55 0.70 1 : 30 �Spin Speed Reduction� button

Synthetics 40 2.5 50 0.50 1 : 15 � Every programme has an automatic predefined maximum spin speed.

Programme 3.0 35 0.40 0 : 30 � Press the button to set another spin speed.

Delicates 30 1.5 50 0.50 0 : 45

� If spin speed �0� selected, the final spinning cancelled. The water is drained out only.

Wool 1.0 50 0.50 0 : 40

Handwash cold 1.0 0.20 0 : 35

PROGRAMME START
Open tap and press button. The pilot lamp of the Start/Pause � � starting programme, the sequence indication runs from left to right through Wash, Rinse,

Prewash cycle increases programme duration by approximately 15 min. Consumption values were measured button lights up. The indicator lamps show sequence reached in the programme. After normalized conditions in compliance with Standard IEC 60 456. The data on the �Energy Label� refer to programme �Coloured Cotton 60° C�. Consumption data home may vary with respect to the values in table in relation to water supply pressure temperature, load and the type of wash. Spin. When sequence of programme is finished the corresponding lamp goes out. * To reduce temperature, some cold water is added at end of the main wash cycle, before DOOR LOCK pump drains the water out. During first 15 minutes of cotton and synthetics programmes the door can be opened

ADD DETERGENT, CLOSE DOOR AND SELECT THE PROGRAMME for adding further laundry.

Add detergent as described chapter �Detergent and Additives� in booklet. The door can be opened when the �Door Free� indication is shining. 1. Turn selector knob to the desired programme and temperature. PROGRAMME END � The remaining time display shows duration of the chosen programme (in hours � All lights of the programme sequence indication are off. A short audible tone 1. Turn programme selector to the � � position. 2. Turn the water supply tap off.

2. The programme sequence and the predefined spin speed indication corresponding to

minutes) and pilot lamp of the Start/Pause � � button is flashing. sounds three times.

the selected programme lights up.

PRESS ANY DESIRED OPTION BUTTON(S). The pilot lamp lights up. 3. Open door and unload the machine. CHANGE THE AND OPTIONS AFTER PROGRAMME START
1. Press Start/Pause � � button to pause the programme. The light flashes. 2. Select the new programme, any options and another spin speed if you want it.

TO CANCEL A PROGRAMME BEFORE THE END
1. Press Start/Pause � � button to pause the programme. The light flashes. 2. Set programme selector to �Drain�. The spin indicators show �0� and the remaining time shows 2 minutes. 3. Press Start/Pause � � button to start the drain programme.

An audible tone sounds if the combination of programme, additional options and temperature is not possible. Unsuitable combinations of options are deselected automatically. �Prewash� button 3. Press Start/Pause � � button again. The new programme continues at the same � Only for heavily soiled loads (for example sand, granular dirt) sensible. The cycle time position where the previous programme was interrupted. Do not add detergent for this increases by approximately 15 min. programme. �Intensive Rinse� button � A further rinse cycle is added. � This option is particularly suitable for areas with very soft water washing baby linen and helps people with allergies. �Rinse Hold� button � The laundry remains in last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing. � This option is particularly recommended for the programme �Synthetics� or �Delicates�. � This function is particularly useful if you want postpone spinning to a later time.