|
|
|
Who's Online
There currently are 5561 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual is complete and very readable.It was a great help for my two ICF5800L.The first one had the dial cord broken,and without the service manual it is impossible to replace it.Thank.Olivier.
 ;
This is a top quality manual. You couldn't get better if you had the original and scanned it yourself. Best price on the net as well. Diagrams are clear and complete, text is sharp and easy to read. Granted you don't get the manual the second you click pay, but the few hours you have to wait for it to be available for download isn't a problem at all. This is a very reliable company.
Very VERY pleased with the product, and will buy others. Thanks!
;
In a word AWESOME.
I never expected the quality and abundant content that I got with this manual. Everything you'd ever want to know from a service perspective is found in this manual, along with... as a bonus, operating instructions on how to use the unit. WOW. Very impressed with the quality of the manual. You won't be disappointed if you're looking for the EVS900 service manual.
;
I thank Owen-Manuals.com for the wonderful service rendered to me, and this manual which I purchased helped me a lot in servicing my Denon System, which was lying in a dead state.
Thanks Owner-Manual.com
;
I purchased this manual to repair my Teac set and with the support of this manual I rectified the problem.
Thanks Owner-Manuals.com
SECTION 2 SERVICE NOTE
[Service Mode]
Mode which enables the mechanism to be operated with the MAIN board opened.
TP50
[MAIN Board]
AF oscillator + � 50K� TO PLUNGER FF ND701 REW TO MOTOR TP52 BATT SQUARE WAVE (SINE WAVE) 10Hz, �3.5dB BATT
1. Setting 1) Refer to �Disassembly� and remove the cabinet and open the MAIN board. 2) Connect the MAIN board to the motor and plunger using a jumper wire. Use �Extension tool (1-769-143-11) (one set 10 tools)� to make connection simple. 3) Short-circuit theTP52 and GND by soldering. 4) Turn OFF the BL SKIP switch. 5) Apply a square wave signal or a sine wave signal to TP52. (see the right figure) 6) Supply 1.3V to the battery terminals (+) and (�) using a stabilized power supply. 2. Preset State This state must be set to set the PLAY, FF, and REW modes. 1) Check that the lever (NR SW) is at the center and F/R switch (S701) is at the center. If not, set the preset state as follows. 2) Move the N/R switch (S701) according to the side faced by the lever (NR SW). 3) Turn OFF the stabilized power supply switch once and then turn it ON again so that the lever (NR SW) can be moved. Move the N/R switch (S701) according to this timing and set to the center. 3. FF REW Mode 1) Check the �2. Preset State� and press the FF switch and REW switch. 4. PLAY Mode 1) Check the �2. Preset State�. 2) Press the � switch. The lever (NR SW) will move to the F side once and then to the R side. Move the N/R switch (S701) according to this timing to set the PLAY (R side) mode. Press the � switch another time and move the N/R switch (S701) according to the movement of the lever (NR SW) to set the PLAY (N side) mode.
Note 1: If the above cannot be performed, start again from preset. Note 2: Use the remote control �, p, FF, and REW switches as much as possible. If the remote control is not available, do not touch switch with the hand and use something with a round tip to press them. Note 3: By using a headphone, the timing for moving S701 can be known by the beep.
� Side A � � Side B �
IC702 PH701 S701
N SIDE CENTER
R SIDE
[Lever (NR SW)]
Center R side Lever (NR SW) F side
�4�
|
|
|
> |
|
