PANASONIC WVCP242EX
Owner's Manual

4. Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera when it is dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. Afterwards, wipe off the remained part of the detergent in it with a dry cloth.

objects. Otherwise, blooming or smear may be caused. 7. Do not operate the camera beyond its specified temperature, humidity or power source ratings. Use the camera under conditions where temperature is between �10 °C - +50 °C {14 °F 122 °F}, and humidity is below 90 %. The input power source is 120 V AC 60 Hz for WV-CP240EX, 12 V DC for WV-CP242EX, and 24 V AC 60 Hz for WV-CP244EX.

CONNECTIONS
A. WV-CP240EX (120 V AC 60 Hz)
Connect the power cord to an electrical outlet of 120 V AC 60 Hz.

SPECIFICATIONS
Mounting the Lens
Caution: Before you mount the lens, loosen the screw on the side of the camera, and rotate the flange-back adjusting ring clockwise until it stops. If the ring is not at the end, the inner lens or CCD image sensor may be damaged. q Mount the lens by turning it clockwise on the lens mount of the camera. w Connect the lens cable to the ALC Lens Connector on the side of the camera. Pick-up Device: Scanning Area: Synchronization: Scanning System: Scanning: Horizontal: Vertical: Horizontal Resolution: Video Output: Signal-to-Noise Ratio: Electronic Light Control: Minimum Illumination:
Focus Fixing Screw
c

Color CCTV Camera

B. WV-CP242EX (12 V DC)
Connect the power cord to the DC 12 V IN terminal on the rear panel of the WVCP242EX.

768 (H) x 494 (V) pixels, Interline Transfer CCD 4.92 (H) x 3.70 (V) mm (Equivalent to scanning area of 1/3" pick-up tube) Internal, Line-locked or Multiplexed vertical drive (VD2), selectable 2 : 1 interlace 525 lines / 60 fields / 30 frames 15.734 kHz 59.94 Hz 480 TV lines 1.0 V[P-P] NTSC composite 75 � / BNC connector 50 dB (Equivalent to AGC Off, weight On) Equivalent to continuous variable shutter speed between 1/60 s and 1/15 000 s 1.5 lx {0.15 foot-candle} at F1.4 1.1 lx {0.11 foot-candle} at F1.2 SHARP or SOFT, selectable C-mount or CS-mount, selectable �10 °C - +50 °C {14 °F - 122 °F} Less than 90 % WV-CP240EX: WV-CP242EX: WV-CP244EX: 120 V AC 60 Hz, 3.6 W 12 V DC, 270 mA 24 V AC 60 Hz, 3.3 W

Operating Instructions
Model Nos.

5. Clean the CCD faceplate with care. Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped

(Lens Option)

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

<WV-CP240EX>

12 V DC (10.5 V - 16 V)

Resistance of copper wire [at 20 °C {68 °F}]
Ns1005-0 3TR004221AAA Printed in China
ALC BLC ON VIDEO SHARP INT

w

ALC BLC ON VIDEO SHARP INT

Copper wire size (AWG)
LOCK

#24 (0.22 mm2) 0.078 0.026

#22 (0.33 mm2) 0.050 0.017

#20 (0.52 mm2) 0.03. 0.010

#18 (0.83 mm2) 0.018 0.006

VIDEO OUT
DC ELC SOFT OFF LL

Resistance �/m Resistance �/ft

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

Caution: Before attempting to operate this product, please read the label on the surface of the unit.

<WV-CP244EX>
AC 24V IN GND

DC

ELC

SOFT

OFF

LL

� Calculation of maximum cable between camera and power supply :

length

1

2

This Class A digital apparatus complies with Canadian ICES-003.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Caution for Mounting the Lens
VIDEO OUT
ALC BLC ON VIDEO SHARP INT

10.5 V DC � VA � (R x 0.42 x L) � 16 V DC The lens mount should be a C-mount or CS-mount L : Cable length (meters)
ALC BLC ON VIDEO SHARP

DC

ELC

SOFT

OFF

LL

For U.S.A

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the SA 1966 literature accompanying the appliance. Power disconnection. Unit with or without ON-OFF switches have power supplied to the unit whenever the power cord is inserted into the power source; however, the unit is operational only when the ON-OFF switch is in the ON position. The power cord is the main power disconnect for all units.

SA 1965

FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user�s authority to operate this equipment.

q ALC Lens Connector Supplies power and control signals to an auto iris lens (not supplied).

ON: Select this mode when a strong light such as a spotlight is in the background. OFF: Normal picture. !1 Detail/Aperture Level Selector [SHARP, SOFT] The detail/aperture level can be selected with this selector. Set it to the desired position while observing the picture on the monitor. SHARP: Normal position. SOFT: Select this position when a Quad System is connected to this camera. !2 Automatic Light Control/Electronic Light Control Selector [ALC, ELC] Lets you select the mode according to the lens type used. ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera. ELC: Select this mode when a fixed iris lens or manual iris lens is used with this camera. !3 Lens Drive Signal Selector [VIDEO, DC] Lets you select the mode according to the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector. VIDEO: Select this mode if you are using a auto iris lens that requires a video drive signal. DC: Select this mode if you are using a auto iris lens that requires a DC drive signal.

The serial number of this product may be found on the surface of the unit. You should note the serial number of this unit in the space provided and retain this instruction as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No.

w Flange-back Adjusting Ring This ring adjusts the back-focal distance or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CSmount lens. e Lens (option) r Mount Adapter The camera mounting screw hole is for mounting the camera onto a mounting bracket. The camera is originally designed to be mounted from the bottom, however, a topmounting type is also available. To mount from the top, remove the mount adapter from the bottom of the camera by removing two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket. Make sure that two original screws are used when mounting the mount adapter; longer type screws may damage inner components, too shorter type screws may cause the camera drop. t Focus Fixing Screw

WARNING: � This apparatus must be earthed. � To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture. � The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, should be placed on the apparatus. � All work related to the installation of this product should be made by qualified service personnel or system installers.

PREFACE
Panasonic�s WV-CP240EX/CP242EX/CP244EX series digital signal processing color CCD cameras introduce a new level of high picture quality and high resolution through the use of a 1/3-inch interline transfer CCD image sensor having 768 horizontal pixels (picture elements), and digital signal processing LSI�s. This model offers cuttingedge technology for advanced video surveillance.

FEATURES
1. The following functions are built in. (1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) Automatic Gain Control (AGC) +15 dB and Automatic Tracing White Balance (ATW) (3) Camera synchronization mode selectable between internal (INT), Line-locked (LL) for WV-CP240EX and WV-CP244EX and Multiplexed Vertical Drive (VD2). 2. Minimum illumination of 1.5 lx {0.15 foot-candle} at F1.4 3. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off) 4. Horizontal resolution of 480 TV lines 5. Auto iris lens control selectable between video signal and DC power supply.

y Power Cord (only for WV-CP240EX) Connect this power cord to an electrical outlet of 120 V AC 60 Hz. u DC 12 V Input Terminal [DC 12V IN] (only for WV-CP242EX) This terminal is for connecting the 12 V DC power supply cord. i AC 24 V Input Terminal [AC 24V IN] (only for WV-CP244EX) This terminal is for connecting the 24 V AC 60Hz power supply cord.

!4 Video Output Connector [VIDEO OUT] This connector is for connecting with the VIDEO IN connector of the video monitor. Whenever the multiplexed vertical drive (VD2) signal is supplied to this connector, the camera synchronization mode is automatically set to Vertical Drive.

PRECAUTIONS
1. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service personnel for servicing. 2. Handle the camera with care. Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage. 3. Do not expose the camera to rain or moisture, or try to operate it in wet areas. This product is designed for indoor use or locations where it is protected from rain and moisture. Turn the power off immediately and ask a qualified service personnel for servicing. Moisture can damage the camera and also create the danger of electric shock.

o Synchronization Mode Selector [INT, LL] (only for WV-CP240EX and WVCP244EX) Selects the camera synchronization mode as either internal sync mode (INT) or line-lock mode (LL). INT: Sets to internal 2:1 interlace. LL: Sets to Line-lock mode. !0 Back Light Compensation Mode Selector [BLC ON, OFF] Lets you select the mode according to the position of the object and light conditions on the screen.

Cautions: � Connect to 12 V DC (10.5 V-16 V) or 24 V AC (19.5 V-28 V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the power is supplied from a 24 V AC power source. � To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the DC 12 V or AC 24 V Input Terminal.

c

cs

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

<WV-CP242EX>
DC 12V IN

R : Resistance of copper wire (�/meter) VA : DC output voltage of power supply unit

(1"-32UN) and the lens weight should be less than 450 g {0.99 lbs}. If the lens is heavier, both the lens and camera should be secured by using the supporter. The protrusion at the rear of the lens should be as shown in the diagram.

Camera Mounting Screw Holes
VIDEO OUT
ALC BLC ON VIDEO SHARP DC SOFT

Fixing Screws
L standard = Mount Adapter L minimum = L maximum =

VA � 12 (meters) 0.42 x R VA � 16 0.42 x R VA � 10.5 0.42 x R (meters) (meters)

DC

ELC

SOFT

OFF

ELC

OFF

C. WV-CP244EX (24 V AC 60 Hz)
Connect the power cable to the AC 24 V IN terminal on the rear panel of the WVCP244EX.
AC 24V IN GND

C-mount: Less than 13 mm {1/2"} CS-mount: Less than 8 mm {5/16"}

1

2

24 V AC, 60 Hz (19.5 V - 28 V)

Recommended wire gauge sizes for 24 V AC line
Copper wire size (AWG) Length of Cable (Approx.) (m) (ft) #24 #22 #20 #18 (0.22 mm2) (0.33 mm2) (0.52 mm2) (0.83 mm2) 95 314 150 495 255 842 425 1 403

Caution: To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the DC 12 V or AC 24 V Input Terminal.

Video Cable
1. It is recommended to use a monitor whose resolution is at least equal to that of the camera. 2. The maximum extensible coaxial cable length between the camera and the monitor is shown below.
Type of coaxial cable Recommended (m) maximum cable length (ft) RG-59/U RG-6U RG-11/U RG-15/U (3C-2V) (5C-2V) (7C-2V) (10C-2V) 250 825 500 1 650 600 1 980 800 2 640

FOCUS OR FLANGE-BACK ADJUSTMENT
The following adjustment should be made by qualified service personnel or system installers. q Loosen the focus fixing screw on the side of the camera. CS/C switching line Focusing of Focusing of CS-mount lens C-mount lens w Turn the flange-back adjusting ring to the desired position. Caution: When the C-mount lens is mounted, do not rotate the ring counterclockwise by force after it stops. If the ring is rotated by force, the inner lens or CCD image sensor may be damaged. e Tighten the focus fixing screw on the side of the camera. Caution: Tightening the screw by force will cause damage to the screw or deviation of focus.
Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America
Security Systems www.panasonic.com/security For customer support, call 1.877.733.3689 Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Zone Office Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 Central: 1707 N. Randal Road, Elgin, IL 60123 Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 Western: 6550 Katella Ave., Cypress, CA 90630

LOCK

Focus Fixing Screw Flange-back Adjusting Ring

c

s

c

cs

WV-CP240EX WV-CP242EX WV-CP244EX

applicator and ethanol. 6. Never face the camera towards the sun. Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright Caution: To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the DC 12 V or AC 24 V Input Terminal.

@!

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

Detail: Lens Mount: Ambient Operating Temperature: Ambient Operating Humidity: Power Source and Power Consumption:

q

Dimensions (without lens): Weights (without lens):

67 mm (W) x 65 mm (H) x 123 mm (D) {2-5/8" (W) x 2-9/16" (H) x 4-13/16" (D)} WV-CP240EX: WV-CP242EX: WV-CP244EX: 0.48 kg {1.06 lbs} 0.3 kg {0.66 lbs} 0.33 kg {0.73 lbs}

Weights and dimensions indicated are approximate. Specifications are subject to change without notice.

STANDARD ACCESSORIES
Body Cap............................................................................................1 pc. Operating Instructions (this document) .............................................1 pc. Warranty card ....................................................................................1 pc.

OPTIONAL ACCESSORIES
Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LF4R5C3A, WV-LF9C3A, WV-LZA61/2S WV-LZ62/8S

Panasonic Canada Inc.

5770 Ambler Drive,Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 http://www.panasonic.ca

Panasonic Sales Company Division of Panasonic Puerto Rico Inc.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina P.R. 00985(809)750-4300

© 2005 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.