|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
High-quality scanning. Detailed description. Recommend for all technician. A+++
;
This is a good quality scan of the original Service Manual from Nordmende, Germany. Contains the circuit diagram, PCB layout, adjust/tune instructions as well. It is NOT in English but in GERMAN language! That was quite right for my german friend from the lower east side in Berlin.
 ;
Received via e-mail this PDF manual is worth the money. This is a quality scan of a manual in excellent condition and is just as good as having the original manual in hand. I have later seen the original manual and it was printed in colour, but this particular manual is black & white but scan resolution is high end quality! All drawings and pictures are presented in great detail. So, nearly perfect score in my opinion.
If you own the turntable you also should own the manual!
;
I was very satisfied with the service manual I ordered and downloaded. I will definitely buy again from this seller.
;
Great product. Recieved it fast...exactly as advertised.
XG-V10XU
1. Adjusting the mirror optical axis
The optical axis must be readjusted to correct possible eclipse that occurs with the R, G or B LCD panel. This readjustment is usually required when an optical part in the optical mechanism has been replaced, and may be needed when a LCD panel has been replaced. 1. Disconnect the LCD flat cable. 2. Get the lamp on. Be sure to start the cooling fan too. (Eclipse with the R LCD panel: Screen edges appearing in cyan) 3. Loosen the lock screws of the M5 adjusting lever. 4. Watching the image on the screen, turn or slide the M5 adjusting lever until the eclipse disappears from the screen. Now tighten up the lock screws. (Eclipse with the G LCD panel: Screen edges appearing in magenta) 3. Loosen the lock screws of the M3 adjusting lever. 4. Watching the image on the screen, turn or slide the M3 adjusting lever until the eclipse disappears from the screen. Now tighten up the lock screws. (Eclipse with the B LCD panel: Screen edges appearing in yellow) 3. Loosen the lock screws of the M6 adjusting lever. 4. Watching the image on the screen, turn or slide the M6 adjusting lever until the eclipse disappears from the screen. Now tighten up the lock screws.
2. Adjusting the orientation of polarizer
The contrast must be optimized when the polarizer or an optical mechanism part has been replaced. 1. Turn on the power. 2. If the background is blue, clear the screen and get it black. 3. Loosen the two lock screws of the polarizer (two for each plate). 4. Press the heads of the lock screws in the arrow directions until the onscreen contrast becomes best. Finally tighten up the lock screws.
3. Adjusting the PBS
This adjustment may be required when the optical mechanism has been disassembled. Colors uneven on the right and left halves onscreen can be corrected here. Usually there is no need to make this adjustment. It is enough to have the lamp adjusting groove in alignment. 1. Turn on the power. 2. Loosen the PBS lock screw. 3. Feed a white-only signal, or call the process mode and get the screen white only. 4. Put the eccentric screwdriver (9EQDRiVER-NV1A) in the PBS adjusting groove. 5. Watching the image on the screen, turn the eccentric screwdriver until the right-and-left colors onscreen become most even. Finally tighten up the lock screw.
4. Adjusting the lamp optical axis
The lamp optical axis is optimized to obtain the best color evenness and brightness. Usually there is no need to make this adjustment because the replacement lamp unit (BQC-XGV10WU/1) has been delivered factory-adjusted. 1. Turn on the power. 2. Loosen the three lamp lock screws. 3. Feed a white-only signal, or call the process mode and get the screen white only. 4. Put the eccentric screwdriver (9EQDRiVER-NV1A) in the lamp adjusting groove. 5. Watching the image on the screen, turn the eccentric screwdriver until the right-and-left colors onscreen become most even. Finally tighten up the lock screws.
27
|
|
|
> |
|
