|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very good quality original datasheet!I like this amazing website!!!!!!
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
TUNER SECTION
Cautions during repair
0 dB = 1 µV
When the tuner unit is defective, replace it by a new one because its internal block is difficult to repair.
FM Auto Scan/Stop Level Adjustment Setting : SOURCE button : FM FREQUENCY SELECT switch (C8100) : FM 200K
FM RF signal generator antenna terminal
TEST MODE
This set have the test mode function. In the test mode, FM Auto Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments can be performed easier than it in ordinary procedure. <Set the Test Mode> 1. Set the �OFF� mode. 2. Push the preset 4 button. 3. Push the preset 5 button. 4. Press the preset 1 button for more than two seconds. 5. Then the display indicates all lights, the test mode is set. <Release the Test Mode> 1. Push the OFF button. Note on Adjustment The adjustments of tuner section, should be performed according to the following sequence. 1. FM Auto Scan/Stop Level Adjustment 2. FM Stereo Separation Adjustment (WIDE) 3. FM Stereo Separation Adjustment (NARROW) 4. FM RDS S-Meter Adjustment (XR-C8100R only) 5. AM (MW) Auto Scan/Stop Level Adjustment
0.01 µF
Carrier frequency : 97.9 MHz (C8100) 98.00 MHz (C8100R) Output level : 22 dB (12.6 µV) Mode : mono Modulation : 1 kHz, 22.5 kHz deviation (30%)
Procedure : 1. Set to the test mode. 2. Push the SOURCE button and set to FM. Display
SHUF
*1
*2
REG
3. Push the preset 3 button. Display
SHUF
*1 *2
REG
4. Adjust with the volume RV2 on TUX10 so that the �FM� indication turns to �FM0� indication on the display window. But, in case of already indicated �FM0�, turn the RV2 so that put out light �0� indication and adjustment. Display
SHUF
*1 *2
REG
*1 : XR-C8100R has the �98.00� displayed. *2 : �REG� is displayed only for XR-C8100R. Adjustment Location : See page 28.
� 25 �
|
|
|
> |
|
