|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
;
Copy of genuine owners/operators manual, very useful
;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
Chapter 11. Using the XV-88 as a GM Sound Module (GM Mode)
Making Effects Settings in GM Mode (EFFECTS)
In GM mode, a GM-exclusive Chorus and Reverb can be used. Chorus and Reverb can be set independently. Chorus: Adds depth and spaciousness to the sound. Reverb: Adds the reverberation characteristics of halls or auditoriums.
OUTPUT
fig.11-03
Output Assign (Output Assign/Output Level)
Sets the direct sound�s output method and volume for each Part. OUTPUT A: Output to the OUTPUT A (MIX) jacks in stereo. OUTPUT B: Output to the OUTPUT B jacks in stereo. The value on the right sets the Part volume.
In GM mode, you cannot use Multi-effects.
The XV-88�s onboard effects can be turned on/off as a whole. For details, refer to �Turning Effects On/Off� (p. 105).
If the Mix/Parallel parameter (SYSTEM/SETUP/ SYSTEM SETUP) is set to MIX, all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 169).
Basic Process of Making Effects Settings
When applying effects in GM mode, the following procedure is used to make the settings. � Chorus and Reverb are output in mono at all times. � The output destination of the signal after passing through the Chorus is set with the Out parameter (GM/ EFFECTS/GM CHORUS) (p. 195). � The output destination of the signal after passing through the Reverb is set with the Out parameter (GM/ EFFECTS/GM REVERB) (p. 195).
1. Setting the Output Method of the Direct Sound (Output Assign)
The settings made here determine for each Part whether or not the jack used to output the sound, and the type of output (stereo or mono). � (p. 194)
2. Setting the Amount of Each Effect Applied (Send Level)
Sets the level (volume) of each effect signal to be sent for each Part. � (p. 194)
Chorus (Chorus Send Level)
Adjusts the amount of Chorus for each Part. If you don�t want to add the Chorus effect, set it to 0.
Reverb (Reverb Send Level)
Adjusts the amount of Reverb for each Part. If you don�t want to add the Reverb effect, set it to 0.
3. Making Chorus Settings
Select the Chorus type to be used, and set each of the parameters for the selected Chorus. � (p. 195)
4. Setting the Output Destination for the Sounds Passing Through the Chorus
Select the output jack from which the sounds passing through the Chorus will be output. You can also apply Reverb to the sound that passes through Chorus. � (p. 195)
5. Making Reverb Settings
Select the Reverb type to be used, and set each of the parameters for the selected Reverb. � (p. 195)
6. Setting the Output Destination for the Sounds Passing Through the Reverb
Select the output jack from which the sounds passing through the Reverb will be output. � (p. 195)
194
 $4.99 XV-88 ROLAND
Quick Start Quick start guide ( sometimes called quick guide ) contains most important information on how to use…
|
|
|
> |
|
