|
|
|
Who's Online
There currently are 5979 guests online. |
|
Support Info
First point of contact:
All trademarks are the property of their respective owners |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
High quality scan of the manual, very quick and easy download and very important, a truly honest price. thanks
 ;
Minden rendben, de két megjegyzés, az ábrák nehezen kivehetők és a fizetés után 24 órát kell várni a letöltésre.
;
Manual correct, and complete. Downloads cleanly. Format of manual was presumably difficult to PDF to A4, but works reasonably well.
;
This was a hard to find manual. When I did find it , some sites wanted way too much for the file.
Owner-manual .com had it for a really reasonable price. Not only that but it was sent very quickly and was a quality scanned document, unlike some others I purchased from a different site.
Good job guys!!
Larry
;
Fast and courteous service. Product delivered as described. Thank you.
For healthier homes
45
2
6
Using Turbo nozzle 5540
Precautions: Only use nozzle on carpets with a pile depth under 15 mm. Do not use on animal skins or rugs with long fringes. To avoid damaging your carpet, do not keep nozzle stationary whilst brush is rotating. Do not pass nozzle over mains cable and switch off nozzle immediately after use. 14 15 Attach turbo nozzle 5540 to tubes. Note: Suction can also be regulated on turbo nozzle by opening/closing air vent 5540. Cleaning Turbo nozzle 5540 Disconnect from mains and remove entangled threads from brush by snipping threads with scissors. Open cover to remove any debris from inside nozzle. Dust bag indicator and changing the dust bag The dust bag should be changed when full. 5505/10/15/20/22/25/28 the dust bag indicator window will turn red when filling and completely red when full. 5530/33/35/36/40 the dust bag indicator window will light up when full. If the dust bag should accidentally get broken in the cleaner, take cleaner to Electrolux Service Centre for cleaning. To check the dust bag, the cleaner must be switched on, with all attachments connected and off the floor. The dust bag full indicator may signify that the bag is blocked (occasionally caused by very fine dust) which will cause loss of suction and may result in overheating. If this occurs change the dust bag even if it is not full. To change the dust bag: A) Open the cleaner cover. B) Pull the sliding tab to remove the dust bag. C) Insert new dust bag by sliding the bag slots into the holder. Close cover. We recommend the dust bag is changed: * after using a carpet cleaning powder * if there is a bad smell from the cleaner, then you should also change/clean the filter Note: Use only Electrolux original dust bags (ref.E54A) and filters: Micro filter (ref. EF17) Washable, reusable HEPA filter (ref. EF25a) Dust bag safety device To avoid damaging the cleaner, do not use it without a dust bag. A safety device is fitted which prevents the cover closing without a dust bag. Do not attempt to force cover shut. Changing/Cleaning the filters Never use the cleaner without the filters in place. The Motor Protection filter should be changed twice a year for normal usage. To change Motor Protection filter: D) Open the cleaner cover. E) Remove filter and covering strip. F) Important: Insert new filter with original covering strip securely in place. Close cover.
The Micro filter 5510/15/20/25/28 should be changed every fifth dust bag. To change Micro filter: G) Open the filter cover. H) Replace filter and close cover ensuring it is properly fastened. The HEPA filter should be cleaned when the indicator light is on 5530/33/35/36/40 or every fifth dust bag 5522. To clean the HEPA filter: I) Open the filter cover and remove filter unit. J) Rinse the inside (dirty side) of the filter unit under warm tap water only. Do not use cleaning agents and avoid touching the delicate filter surface. Tap the filter frame to remove excess water. Repeat cleaning procedure four times and allow the filter to air dry. The original filtering performance is now restored. Replace the unit back into the cleaner and close cover ensuring it is properly fastened.
16
Troubleshooting
1. Power: If the electric power does not come on, disconnect from mains and check plugs, cable and fuses where appropriate. 2. Blockage/dirty filters: The cleaner may switch itself off in event of severe blockage or excessively dirty filters (on 5530/33/35/36/40 overheat indicator will flash). In such cases, disconnect from mains and allow to cool for 30 minutes. Clear blockage and/or replace filter(s) and restart. The clearing of blocked hoses is not covered by the guarantee. To avoid blockages and maintain suction efficiency, the floor nozzles should be cleaned regularly using the hose handle. Please see additional Electrolux information towards the back of this booklet. 3. Water: If water is sucked into the cleaner the motor must be changed at an Electrolux Service Centre. If you have any comments on the cleaner or the Instruction for Use Booklet please e-mail us on: [email protected]
ANY PROBLEMS?
Something missing?
Don�t understand the instructions? DON�T TAKE Need more help?
IT BACK TO THE SHOP
We are only a telephone call away. CUSTOMER HELPLINE for the UK
08706 055 055
Local call cost Australia wide: 1300 369 333
|
|
|
> |
|
