|
|
|
Who's Online
There currently are 6024 guests and
19 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Complete service manual in very good scanning quality with all schematic and PWB graphics as well as assembly & maintenance instructions. A slight drawback is that the rastering of the PWB graphics sometimes makes it a bit difficult to follow fine traces, but no showstopper.
;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site. Thank you very much
 ;
Service manual in good quality, it was very helpful to me. Perfect service, I am very satisfied.
Jochen Kelm
;
Exellent manual ,it was in great condition,and got all the info i expected,5 stars!!
;
I searched the Internet exhaustively for this manual and Owner-Manuals was the least expensive...but provided an excellent reproduction within 4 hours. Very satisified.
Power supply
Battery used
Type Lithium battery Lithium battery Model CR2032 CR2032 Quantity 2 1 Application Unit operation Memory backup
7. Set the clock to the correct time.
Synchronization
Supplied Items
Sharp Electronic Organizer One 3.5" Floppy Disk(PC Interface Software) PC Interface Cable PC Interface Software User�s Guide
Do not remove both the operation and memory backup batteries at the same time. Doing so will clear the memory of its contents. Be sure to write down any important infomation stored in memory before replacing the batteries.
System Requirements
Windows ® 98, or Windows ® 95 IBM-compatible 486 or Pentium processor (33 MHz or greater) 8MB free hard disk space 16MB RAM available VGA monitor or better Microsoft ® Mouse or compatible Pointing Device 3.5" disk drive One available serial port with D-sub 9-pin connector
1. Precautions
Since improper use of the batteries may cause leakage or explosion, strictly observe the following instructions. Insert the battery with its positive side (+) correctly positioned. Never throw batteries into a fire because they might explode. Keep batteries out of reach of children. When batteries become weak, remove them from the Organizer immediately to avoid battery leakage and corrosion inside the Organizer. Because the batteries in the Organizer were installed at the factory, they may become depleted before the specified expiration time is reached.
Connecting Your Organizer to a PC
2. Operating Batteries Replacement (1) Battery replacement time
When " BATT " is displayed, immediately replace the batteries with new ones. If the battery level is very low, the alarms or the key touch tone may not sound, or similarly the Backlight may remain on for less than the set interval or it may not function. Continued use of the Organizer with consumed batteries can alter or clear the memory contents. Memory contents may be lost if the batteries are improperly replaced or if the following instructions are disregarded. Make sure the power is turned off before replacing the batteries. Do not press ON u nti l the ba tter y r eplacem ent pr ocedur e is completed. 1. Turn off your PC and the Organizer. 2. Connect the standard 9-pin connector of the PC interface cable into a COM port on your PC.
Your PC Connected to the option port (COMPUTER LINK) of an Organizer PC Interface Cable (supplied)
(2) Replacing the batteries
1. Press OFF to turn the power off. 2. Loosen the screw (counter clockwise) and remove the battery holder cover on the back of unit. (Fig. 1)
( F ig .1 )
NOTE
Using a 25-pin connector instead of the standard 9-pin connector requires an additional adapter. 3. Connect the other end of the PC Interface Cable into the option port located on the left (or right) side of the Organizer.
3. Remove the used batteries using a ball-point pen or similar object. (Fig. 2) Do not use a mechanical pencil or sharp pointed object.
( F ig .2 )
4. Install two new batteries with the positive sides (+) facing up. 5. Replace the holder cover and secure it with the screw. 6. Press ON to turn the power on. If nothing appears on the display, press the RESET switch and press and hold ON for two or three seconds.
|
|
|
> |
|
